Ines Pires

Ines Pires

Auto-generated profile, based on publicly available information

Ines Pires

Universidade de Lisboa

Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 January 2014 in Biofabrication
Verified
Journal Article
Closed access
Miguel CastilhoMiguel Castilho
Miguel Castilho
CMClaus Moseke
Claus Moseke
AEAndrea Ewald
Andrea Ewald
UGUwe Gbureck
Uwe Gbureck
JGJürgen Groll
Jürgen Groll
EVElke Vorndran
Elke Vorndran
The 3D printing technique based on cement powders is an excellent method for the fabrication of individual and complex bone substitutes even in the case of large defects. The outstanding bone remodeling capacity of biphasic calcium phosphates (BCPs) containing hydroxyapatite (HA) as well as tricalcium phosphate (TCP) in varying ratios makes the adaption of powder systems resulting in BCP materials to this fabrication technique a desirable aim. This study presents the synthesis and characterization of a novel powder system for the 3D printing process, intended for the production of complexly shaped BCP scaffolds by a hydraulic setting reaction of calcium carbonate and TCP with phosphoric acid. The HA/TCP ratio in the specimens could be tailored by the calcium/phosphate ratio of the starting powder. The scaffolds could be fabricated with a dimensional accuracy of >96.5% and a minimal macro pore size of 300 µm. Independent of the phase composition the printed specimens showed a microporosity of approximately 68%, while the compressive strength strongly depended on the chemical composition and increased with rising TCP content in the scaffolds to a maximum of 1.81 MPa. Post-treatment of the scaffolds with a polylactic-co-glycolic acid-solution enhanced the mechanical properties by a factor of 8. In vitro studies showed that all BCP scaffolds were cytocompatible and enhanced the cell viability as well as the cell proliferation, as compared with pure TCP. Cell proliferation is even better on BCP when compared to HA and cell viability is in a similar range on these materials.

1 January 2003 in International Journal of Adhesion and Adhesives
Verified
Journal Article
Closed access
IPI. Pires
I. Pires
LQL. Quintino
L. Quintino
JDJ.F. Durodola
J.F. Durodola
ABA. Beevers
A. Beevers

1 May 2018 in Additive Manufacturing
Verified
Journal Article
Open access
ALAna Lopez
Ana Lopez
RBRicardo Bacelar
Ricardo Bacelar
IPInês Pires
Inês Pires
Telmo SantosTelmo Santos
Telmo Santos
JSJosé Pedro Sousa
José Pedro Sousa
LQLuísa Quintino
Luísa Quintino


26 July 2013 in Biofabrication
Verified
Journal Article
Closed access
PDF file
Miguel CastilhoMiguel Castilho
Miguel Castilho
MDMarta Dias
Marta Dias
UGUwe Gbureck
Uwe Gbureck
JGJürgen Groll
Jürgen Groll
PFPaulo Rui Fernandes
Paulo Rui Fernandes
EVElke Vorndran
Elke Vorndran
The development of artificial bone substitutes that mimic the properties of bone and simultaneously promote the desired tissue regeneration is a current issue in bone tissue engineering research. An approach to create scaffolds with such characteristics is based on the combination of novel design and additive manufacturing processes. The objective of this work is to characterize the microstructural and the mechanical properties of scaffolds developed by coupling both topology optimization and a low temperature 3D printing process. The scaffold design was obtained using a topology optimization approach to maximize the permeability with constraints on the mechanical properties. This procedure was studied to be suitable for the fabrication of a cage prototype for tibial tuberosity advancement application, which is one of the most recent and promising techniques to treat cruciate ligament rupture in dogs. The microstructural and mechanical properties of the scaffolds manufactured by reacting α/β-tricalcium phosphate with diluted phosphoric acid were then assessed experimentally and the scaffolds strength reliability was determined. The results demonstrate that the low temperature 3D printing process is a reliable option to create synthetic scaffolds with tailored properties, and when coupled with topology optimization design it can be a powerful tool for the fabrication of patient-specific bone implants.

1 July 2012 in Materials Science and Engineering: C
Verified
Journal Article
Closed access
CSCarlos F.L. Santos
Carlos F.L. Santos
Abilio P. SilvaAbilio P. Silva
Abilio P. Silva
LLLuís Lopes
Luís Lopes
IPInês Pires
Inês Pires
ICIlídio Correia
Ilídio Correia