Ki-Chan Woo

Ki-Chan Woo

Auto-generated profile, based on publicly available information

Ki-Chan Woo

Department of Electronics Engineering, Chungbuk National University, Cheongju 28644, South Korea

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 August 2019 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
KWKi-Chan Woo
Ki-Chan Woo
BYByung-Do Yang
Byung-Do Yang
This paper proposes a 0.25V rail-to-rail three stage OTA. The proposed OTA improves a DC gain by inserting an NMOS gate-driven amplifier into the conventional bulk-driven OTA. In addition, it uses an asymmetric self-cascode transistor and an indirect feedback compensation to enhance a DC gain and an unit-gain frequency. At the first stage, the bulk-driven amplifier has a rail-to-rail input, but it has a low DC gain due to a small transconductance. At the second stage, the NMOS gate-driven amplifier enhances the DC gain. At the last stage, the common-source amplifier drives an output load capacitor. The proposed OTA was fabricated using a 65nm CMOS process. Its area is 0.002mm. It consumes 0.026μW at the supply-voltage of 0.25V. The DC gain and unit-gain frequency are 70dB and 9.5kHz, respectively, with the phase margin of 88∘ at the load capacitance of 15pF.

1 January 2019 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
KWKi-Chan Woo
Ki-Chan Woo
JOJae-Mun Oh
Jae-Mun Oh
BYByung-Do Yang
Byung-Do Yang
This brief proposes a dc-dc buck converter using an analog coarse-fine self-tracking zero-current detection (ASTZCD) scheme. The AST-ZCD detects the zero-current by measuring the voltage level across a freewheeling transistor. It adjusts the nMOS turn-off time using an amplifier, capacitors, and current sources instead of large numbers of shift register bits and unit delay cells in the conventional digital self-tracking zerocurrent detection (DST-ZCD). It also reduces the zero-current self-tracking time by using coarse-fine current-sources when the output current transition is large. The proposed dc-dc buck converter was fabricated with a 0.18-μm CMOS process. The AST-ZCD reduces the area by 94%, the power consumption by 80%, and the zero-current self-tracking time by 82% compared to the DST-ZCD.

1 April 2020 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
KWKi-Chan Woo
Ki-Chan Woo
BYByung-Do Yang
Byung-Do Yang
In this paper, a low quiescent output-capacitor-less NMOS low-dropout regulator using a coarse-fine charge-pump circuit is proposed. The proposed charge-pump low-dropout regulator (CP-LDO) achieves the output-capacitor-less LDO using a NMOS power transistor, a comparator, and a coarse-fine charge-pump circuit. It reduces both the quiescent current and the capacitor size of the charge-pump by directly adjusting the gate voltage of the NMOS power transistor. It improves both the transient response and the quiescent power efficiency by coarsely and finely adjusting the gate voltage, respectively. This also can remove the output glitch voltage. The proposed CP-LDO was fabricated using a 65nm CMOS process. Its area is 0.01mm2. The maximum undershoot voltage is 108mV when the load current changes from 0.5mA to 10.5mA within the edge time of 1ns. The total capacitor of the CP-LDO is 7.6pF. The quiescent current is 162nA at VIN=0.5V and fCLK=1MHz. The figure of merit is 0.0013ps.

30 April 2018 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
KWKi-Chan Woo
Ki-Chan Woo
BYByung-Do Yang
Byung-Do Yang
This paper proposes a low-area ternary contentaddressable memory using a don't care reduction (DCR) scheme. In Internet Protocol (IP) address, the prefix bits store “0” or “1,” and the remaining bits store “X” (don't care). The conventional ternary content-addressable memory (TCAM) needs a 2N-bit memory for an N-bit IP address, because its TCAM cell uses 2-bit memory to store a data bit (“0” or “1”) and a don't care (“X”) bit. However, the proposed DCR TCAM (DCR-TCAM) needs a (N + log 2 N)-bit memory for an N-bit IP address. It also stores N-bit data, but it encodes N-bit “X”s into a log 2 N-bit code, storing the first “X” position. The proposed DCR-TCAM performs the function of “X” in the TCAM from the log 2 N-bit code by using additional decoders and bypass transistors. A 256 × 128-bit DCR-TCAM chip was fabricated using a 1.2-V, 65-nm CMOS process. Its area is 0.22 mm 2 , which is only 72% of the conventional TCAM. It expands an effective memory size by applying the data-relocation TCAM scheme. Its energy/bit/search is 0.41 fJ at a clock frequency of 330 MHz.

22 November 2018 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
KWKi-Chan Woo
Ki-Chan Woo
HKHyeong-Ju Kang
Hyeong-Ju Kang
BYByung-Do Yang
Byung-Do Yang

25 September 2019 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
KWKi-Chan Woo
Ki-Chan Woo
HKHyeong-Ju Kang
Hyeong-Ju Kang
BYByung-Do Yang
Byung-Do Yang
This paper proposes unidirectional and bidirectional latch-based thermometer-code shift-registers. They reduce both the area and the power consumption by replacing the D flip-flops with the proposed unidirectional and bidirectional thermometer-code latches. The proposed unidirectional and bidirectional 64-bit thermometer-code shift-registers were simulated using a 65nm CMOS process. They occupy 167μm2 and 226μm2. They consume 5.4μW and 6.5μW at a 100MHz clock frequency with VDD=1.2V. They reduce the areas by 71% and 76% and the power consumptions by 83% and 85% compared to the conventional unidirectional and bidirectional 64-bit shift-registers, respectively.