Takashi Matsui

Takashi Matsui

Auto-generated profile, based on publicly available information

Takashi Matsui

Access Network Service Systems Laboratories, NTT Corporation, Tsukuba, Japan

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 April 2007 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
TMTakashi Matsui
Takashi Matsui
KNKazuhide Nakajima
Kazuhide Nakajima
ISIzumi Sankawa
Izumi Sankawa
This paper numerically describes the design of double-cladding photonic-crystal fiber (DC-PCF) for ultrabroadband compensation over all telecommunication bands (O to L), i.e., ranging from 1260 to 1625 nm. We show that an ultrabroadband compensating DC-PCF can be designed simply by considering the zero-dispersion wavelength and the relative dispersion to the slope at a particular wavelength of a conventional single-mode fiber (SMF). As a result, we reveal that the proposed DC-PCF can successfully compensate for the dispersion of a conventional SMF with an effective dispersion range of plusmn0.4 ps/nmmiddotkm over all telecommunication bands as well as provide an effective area comparable to that of conventional dispersion-compensating fiber

19 December 2016 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
YYYoko Yamashita
Yoko Yamashita
TFTakeshi Fujisawa
Takeshi Fujisawa
SMShuntaro Makino
Shuntaro Makino
NHNobutomo Hanzasa
Nobutomo Hanzasa
TSTaiji Sakamoto
Taiji Sakamoto
KSKunimasa Saitoh
Kunimasa Saitoh
A broadband and low-loss two-mode (LP01/LP11a) multi/demultiplexer (MUX/DEMUX) based on a planar lightwave circuit (PLC) is designed by a wavefront matching method, which is an optimization algorithm of PLC based on the beam propagation method. The calculated transmission loss of the optimized structure is lower than -0.3 dB in the wavelength range from 1400 to 1700 nm. Numerical results show that the proposed structure has large fabrication tolerance compared to the conventional structure. The designed structure is fabricated and broadband characteristics are well-reproduced, showing the usefulness of the proposed MUX/DEMUX.

21 November 2013 in IEEE Photonics Journal
Verified
Journal Article
Open access
MKMotoki Kasahara
Motoki Kasahara
KSKunimasa Saitoh
Kunimasa Saitoh
TSTaiji Sakamoto
Taiji Sakamoto
NHNobutomo Hanzawa
Nobutomo Hanzawa
TMTakashi Matsui
Takashi Matsui
MKMasanori Koshiba
Masanori Koshiba
We investigate the fiber parameters that meet the design conditions for low bending loss and an effectively few-mode operation on few-mode fibers with a step-index profile and a W-shaped refractive index profile for mode-division multiplexing transmission. We also clarify the limits of effective area enlargement and the difference of the effective index while satisfying the design conditions.

21 September 2007 in Applied Optics
Verified
Journal Article
Closed access
PDF file
TMTakashi Matsui
Takashi Matsui
KNKazuhide Nakajima
Kazuhide Nakajima
TSTaiji Sakamoto
Taiji Sakamoto
KSKazuyuki Shiraki
Kazuyuki Shiraki
ISIzumi Sankawa
Izumi Sankawa
We describe the guided acoustic-wave Brillouin scattering (GAWBS) characteristics of hole-assisted fiber (HAF). We clarify numerically and experimentally that the GAWBS spectrum corresponding to a particular acoustic mode is observed for HAF and that the efficiency for that mode can be controlled simply by designing the air-hole size and position. We also reveal the temperature dependence of the GAWBS characteristics in HAF.

7 October 2010 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
TMTakashi Matsui
Takashi Matsui
KNKazuhide Nakajima
Kazuhide Nakajima
KTKunihiro Toge
Kunihiro Toge
TKToshio Kurashima
Toshio Kurashima
MTMakoto Tsubokawa
Makoto Tsubokawa
The macro-bending based fiber identification technique is widely used to identify optical fibers at the worksite. Bending-loss insensitive fibers have been receiving increasing attention, however it is difficult to apply the macro-bending based fiber identification technique to these fibers. In this paper, we propose a new fiber identification technique based on a mechanically induced long-period grating (LPG), and show that the proposed technique can be utilized for a hole-assisted fiber with an extremely low bending loss. We also propose combining the chirped LPG technique with our fiber identification method to simultaneously specify fibers with different structures.

1 January 2011 in IEICE Transactions on Communications
Verified
Journal Article
Closed access
PDF file
KNKazuhide Nakajima
Kazuhide Nakajima
TSTomoya Shimizu
Tomoya Shimizu
TMTakashi Matsui
Takashi Matsui
CFChisato Fukai
Chisato Fukai
TKToshio Kurashima
Toshio Kurashima
The characteristics of hole-assisted fiber (HAF) are investigated both numerically and experimentally in terms of its applicability as a bending-loss insensitive fiber (BIF). We show that HAF with the desired mode-field diameter (MFD), bending-loss and cutoff wavelength characteristics can be roughly designed by taking a few specific structural parameters into consideration. We also show that an optical cord composed of adequately designed HAF realizes satisfactory transmission performance with respect to its multi-path interference (MPI) characteristics. These results reveal that a hole-assisted type BIF will be beneficial for realizing easy and economical installation and maintenance in future access networks.