Nitin.N. Yalamoori

Nitin.N. Yalamoori

Auto-generated profile, based on publicly available information

Nitin.N. Yalamoori


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2014 in Procedia Engineering
Verified
Journal Article
Open access
VSVignesh. V. Shanbhag
Vignesh. V. Shanbhag
NYNitin. N. Yalamoori
Nitin. N. Yalamoori
KSKARTHI KEYAN S
KARTHI KEYAN S
RRR. Ramanujam
R. Ramanujam
KVK. Venkatesan
K. Venkatesan
Al 7075 matrix composites are widely used in structural and aerospace industry because of its higher hardness, wear resistance and strength to weight ratio. But properties such as low formability and poor corrosion resistance restrict its wider usage. Therefore this experiment is performed to investigate distribution of higher percentage of reinforcement in matrix and to study the corrosion behaviour of base Al 7075 alloy and Al 7075 reinforced with 10% wt and 15% wt of Al2O3 fabricated by stir casting method. Metallographic study of composite was carried out using optical microscope, XRD, SEM with EDX. Density of prepared composite was determined by Archimedes principle. Corrosion study was performed in Sea water and industrial environment for three different samples, Al 7075 monolithic alloy, Al 7075 reinforced with 10% and 15% wt of Al2O3 particles. Experiments were conducted using electrochemical analyzer using Tafel Polarization Technique (TPT). From the analysis of SEM images it reveals that pitting corrosion was observed in sea water environment and inter granular corrosion was observed in industrial environment. It was observed that corrosion rate of Al 7075 increases with increase in reinforcement volume and Al 7075 undergoes severe corrosion in sea water environment than Industrial environment. Tafel polarization measurement of corroded Al 7075-Al2O3 (15%wt) in seawater environment and industrial environment is shown belo

1 January 2014 in Procedia Materials Science
Verified
Journal Article
Open access
KVK. Venkatesan
K. Venkatesan
RRR. Ramanujam
R. Ramanujam
VSVignesh.V. Shanbhag
Vignesh.V. Shanbhag
NYNitin.N. Yalamoori
Nitin.N. Yalamoori
DRD.VenkataSubba Reddy
D.VenkataSubba Reddy
This experimental study is done to investigate distribution of Al2O3 (15% wt) having particle size of 20μm in Al-7075 (T6) matrix composite, fabricated by stir casting method and study influence of cutting parameters on surface finish using multi coated carbide inserts. Uniform distribution of Al2O3 particles was observed using microstructure study. The characterization of the prepared samples was carried out using X-ray diffraction and scanning electron microscopy. Machinability study was done on medium duty lathe using multi coated carbide insert. Taguchi L9 orthogonal array method is applied for designing an experiments with the selection of cutting parameter, cutting speed of 80,100,120m/min, feed rate of 0.103, 0.206, 0.296mm/rev, and cutting depth of 0.3, 0.6, 0.9mm. The optimal cutting conditions was found using the signal-to-noise (S/N) ratio for surface roughness parameters (Ra, Rt), cutting force, tool wear according to the “the-smaller-the-better” approach. Taguchi response analysis and ANOVA is used to optimize the parameters influencing the objectives. The optimum cutting levels for surface roughness at cutting speed of 80m/min, feed rate of 0.103mm/rev and depth of cut at 0.3mm, for tool flank wear cutting speed of 120m/min, feed rate of 0.296mm/rev and depth of cut at 0.9mm and for cutting force cutting speed of 120m/min, feed rate of 0.103mm/rev and depth of cut at 0.3mm.In order to achieve good surface finish and reduced tool wear, higher cutting speed and lower feed rate combination is suggested for machining Al-7075(T6) - Al2O3 matrix composite