1 November 2022 in IEEE Transactions on Communications
In this article, we study the joint communication and sensing (JCAS) paradigm in the context of millimeter-wave (mm-wave) mobile communication networks. We specifically address the JCAS challenges stemming from the full-duplex operation in monostatic orthogonal frequency-division multiplexing (OFDM) radars and from the co-existence of multiple simultaneous beams for communications and sensing purposes. To this end, we first formulate and solve beamforming optimization problems for hybrid beamforming based multiuser multiple-input and multiple-output JCAS systems. The cost function to be maximized is the beamformed power at the sensing direction while constraining the beamformed power at the communications directions, suppressing interuser interference and cancelling full-duplexing related self-interference (SI). We then also propose new transmitter and receiver beamforming solutions for purely analog beamforming based JCAS systems that maximize the beamforming gain at the sensing direction while controlling the beamformed power at the communications direction(s), cancelling the SI as well as eliminating the potential reflection from the communication direction and optimizing the combined radar pattern (CRP). Both closed-form and numerical optimization based formulations are provided. We analyze and evaluate the performance through extensive numerical experiments, and show that substantial gains and benefits in terms of radar transmit gain, CRP, and SI suppression can be achieved with the proposed beamforming methods.
10 May 2018 in IEEE Transactions on Antennas and Propagation
Single-frequency full-duplex wireless communication (SFD) can increase the efficiency of bandwidth utilization by ideally doubling the spectral efficiency. SFD can be achieved by reducing the level of the self-interference between the transmitter (TX) and receiver (RX) to the RX noise floor. This paper describes a novel decoupling structure to increase the isolation for a collinear dipole array which retains the omnidirectional radiation patterns of the dipole antennas. The structure is based on a parasitic element which couples power from the TX antenna and reradiates it with orthogonal polarized elements cancelling the original field around the RX antenna. A novel analysis is presented for the decoupling structure in which the phase and amplitude radiation pattern of the decoupling structure is calculated. The obtained isolation is more than 50 dB according to the simulation and measurement for a bandwidth of 11 %, fulfilling the required electromagnetic isolation for a full-duplex system in indoor device-to-device communications.
17 August 2020 in IEEE Antennas and Wireless Propagation Letters
This paper presents a low-cost single-layer printed circuit board (PCB) design of a Rotman lens and an 8-element Yagi-Uda antenna array suitable for radio frequency (RF) beamsteering at 28 GHz. The antenna array realizes 19 dBi gain due to the guiding parasitic elements of each antenna element and a shaped ground plane surrounding the array. The array radiates in a direction parallel to the PCB enabling the possibility for two-dimensional beamsteering by stacking the PCBs. Integrated with an RF switch network, the design has seven switchable beams to the directions -30, -20, -10, 0, 10, 20 and 30. The measured realized gain is still as high as 4 to 10 dBi including losses of the Rotman lens and the RF switches, thanks to the high-gain antenna array design. The array works wideband across 25.5 to 28.5 GHz where broadside beam gains are better than 8 dBi. This is the first paper in literature introducing an experimentally-verified design of a PCB end-fire antenna array at 28 GHz including all necessary components for RF beamsteering, i.e., a Rotman lens and a switch network.
29 June 2021 in IEEE Transactions on Intelligent Transportation Systems
The employment of passive reflectors enables the millimeter-wave automotive radars to detect an approaching vehicle in non-line-of-sight conditions. In this paper, the installation of such reflectors above the sidewalk at an intersection is proposed and studied, avoiding pedestrians’ blockage and road dust effect at ground level. Through the analysis of the backscattering power, it is shown that the suggested scheme may detect an approaching vehicle in the blind zone at distances of 30…50 m to the intersection point. Additionally, the analysis shows that efficient operation is highly dependent on the spatial orientation and size of the reflector. Even a few degrees rotation may change the detecting range by several meters. In turn, the larger area of the reflector may cover longer detecting distances, improving the radar scheme’s overall performance. It is also shown that further performance enhancement can be achieved by employing a C-type radar, contributing an extra 5 dB to the backscattering power relative to an A-type radar. However, despite these improvements, the strongest scattering centre of the detectable vehicle is systematically identified to the bumper zone.
20 June 2023 in IEEE Transactions on Microwave Theory and Techniques
The received radio-frequency (RF) power in far-field RF wireless power transfer (WPT)—with or without simultaneous information transfer—is minuscule due to large propagation loss in wireless media. In such scenarios, adapting to the receiver characteristics by transmit waveform optimization is essential for maximizing the harvested direct current (dc) and, thus, the end-to-end efficiency of an RF WPT system. The receiver efficiency in RF WPT is governed by the RF-to-dc efficiency of the rectifier as well as the impedance mismatch at the antenna and load. In this article, we study the receiver efficiency for any fixed load and, subsequently, present a novel rectifier model that relates the average harvested dc power to the distribution, that is, the histogram, of the instantaneous power levels of the RF signal’s envelope over time. The proposed waveform-to-energy harvesting (EH) model enables us to anticipate the average harvested dc power for any waveform, including communication signals as well, given the knowledge of the power-level distribution. Consequently, we conduct rigorous waveform optimization to maximize the average harvested dc power and determine the digital baseband signal at the transmitter that does so, namely prove that a pulsed tone at appropriate frequency is optimal for RF WPT. We present a multiband test-bed for determining the receiver efficiency for any digital baseband waveform. The efficacy of the proposed model is corroborated through experiments as well as simulations, which confirm that it is operational as well as accurate in practice and that single-sine pulses yield higher efficiency than basic multisine waveforms, while a pulsed phase shift keying (PSK) is preferable for simultaneous wireless information and power transfer (SWIPT).