3 May 2010 in IEEE Transactions on Microwave Theory and Techniques
This paper studies tag properties for optimized tag-to-reader backscatter communication. The latter is exploited in RF identification (RFID) systems and utilizes binary reflection coefficient change of the tag antenna-load circuit. It is shown that amplitude maximization of complex reflection coefficient difference between the two states is not sufficient for optimized tag-to-reader backscatter communication, contrary to what is commonly believed in the field. We provide a general tag load selection methodology that applies to any tag antenna, including minimum scattering antennas as a special case. The method is based on tag antenna structural mode closed-form calculation (given three values of tag radar cross section), employs simple antenna/communication theory, and applies to both passive, as well as semipassive RFID tags.
8 January 2010 in IEEE Transactions on Wireless Communications
This work evaluates opportunistic relaying in the presence of thermal noise as well as interference, when channel sensing is conducted reactively, in slow fading environments. The studied scenario employs a single gateway that provides access towards several destinations with weak links and exploits a network of intermediate relays. In sharp contrast to prior art, no inter-relay channel state information or communication is assumed, no network coding is needed, while low-complexity receivers at each destination are employed. It is shown that information can be relayed without delay, while harvesting benefits of cooperative diversity, even at the presence of interference. The participating relays are required to offer strong paths towards source and destination, while at the same time they are as "isolated" as possible from each other. From that perspective, the notion of relay "usefulness" is redefined in both noise and interference-limited environments, under opportunistic relaying.
26 August 2019 in IEEE Journal of Radio Frequency Identification
In this paper, we propose a new method for the localization of RFID tags, by deploying off-the-shelf RFID equipment on a robotic platform. The constructed robot is capable to perform Simultaneous Localization (of its own position) and Mapping (SLAM) of the environment and then locate the RFID tags around its path. The proposed method is based on properly treating the measured phase of the backscattered signal by each tag at the reader’s antenna, located on top of the robot. More specifically, the measured phase samples are reconstructed, such that the 2π discontinuities are eliminated (phase-unwrapping). This allows for the formation of an optimization problem, which can be solved rapidly by standard methods. The proposed method is experimentally compared against the SAR/imaging methods, which represent the accuracy benchmark in prior-art, deploying off-the-shelf equipment. It is shown that the proposed method solves exactly the same problem as holographic-imaging methods, overcoming the grid-density constraints of the latter. Furthermore, the problem, being calculations-grid-independent, is solved orders of magnitude faster, allowing for the applicability of the method in real-time inventorying and localization. It is also shown that the state-of-the-art SLAM method, which is used for the estimation of the trace of the robot, also suffers from errors, which directly affect the accuracy of the RFID localization method. Deployment of reference RFID tags at known positions, seems to significantly reduce such errors.
10 February 2012 in IEEE Transactions on Communications
This work derives and evaluates single-antenna detection schemes for collided radio frequency identification (RFID) signals, i.e. simultaneous transmission of two RFID tags, following FM0 (biphase-space) encoding. In sharp contrast to prior art, the proposed detection algorithms take explicitly into account the FM0 encoding characteristics, including its inherent memory. The detection algorithms are derived when error at either or only one out of two tags is considered. It is shown that careful design of one-bit-memory two-tag detection can improve bit-error-rate (BER) performance by 3dB, compared to its memoryless counterpart, on par with existing art for single-tag detection. Furthermore, this work calculates the total tag population inventory delay, i.e. how much time is saved when two-tag detection is utilized, as opposed to conventional, single-tag methods. It is found that two-tag detection could lead to significant inventory time reduction (in some cases on the order of 40%) for basic framed-Aloha access schemes. Analytic calculation of inventory time is confirmed by simulation. This work could augment detection software of existing commercial RFID readers, including single-antenna portable versions, without major modification of their RF front ends.
5 July 2005 in IEEE Transactions on Antennas and Propagation
In this paper, a novel technique for the approximation of three-dimensional (3-D) antenna radiation patterns is presented. The proposed method combines the two principal cuts in order to acquire an adequate estimate of the 3-D antenna radiation solid. The absolute error from the theoretical solution is analyzed along with other statistical measures for various types of antenna structures, namely omni-directional and directive arrays. The performance of the method is compared against other existing extrapolation algorithms. The proposed technique exhibits low approximation errors and is easily integrated into 3-D radio propagation planning tools (such as ray-tracing algorithms).
1 April 2021 in IEEE Journal of Radio Frequency Identification
In this paper, we present a prototype method for 3D localization of UHF RFID tags by a moving robot. The proposed method represents an extension of Phase ReLock, in 3D space. Phase measurements are collected by at least two antennas, thus a multi-antenna synthetic aperture is created. We propose a new optimization problem, which involves measurements from all different antennas. Thanks to phase-unwrapping, the new multi-antenna optimization problem preserves its convex-like properties. Consequently, it is solved rapidly by standard optimization techniques. Furthermore, we introduce a confidence metric that can identify measured data, which deteriorate the accuracy of the estimations. These can be removed from the measurements' dataset. We have conducted extensive measurements, employing four antennas on top of a SLAM-enabled robot; i.e., the robot is able to create a map of the unknown environment and continuously estimate its pose inside the map. The proposed method outperforms prior art with respect to accuracy and computation time. It achieves mean 3D error less than 20cm with an estimation-time of only 0.17s per tag on an average laptop.