For vacuum circuit breakers, the anode will change to active mode when the current is high enough. The vapor produced by the anode will become another important source of plasma. In this paper, a three-dimensional (3D) magnetohydrodynamic model considering anode vapor and multiple components is developed to study the vacuum circuit breakers with cup-shaped CuCr contact. The characteristics of arc under the actual magnetic field with different anode temperature distribution and different cathode utilization are simulated. Moreover, the ionization and recombination processes between different kinds of components are considered. The simulation results show that the arc current concentrates toward the center. The current value is high between electrodes slots under the actual magnetic field, which significantly affects the arc characteristics. At the same time, higher anode temperatures will produce more neutral atom vapor area (NAVA). Current is concentrated outside NAVA due to the low conductivity of NAVA. As NAVA expands, the constriction of current on the outside is more severe. The simulation results in this paper are consistent with the experimental results.
22 February 2023 in IEEE Transactions on Plasma Science
With the rapid development of multiterminal high-voltage direct current (HVdc) transmission systems, the research and development of high-speed and stable high-voltage dc circuit breakers have received attention. Among them, mechanical dc circuit breakers based on manual zero-crossing dc breaking technology have been applied in practical projects, owing to their small size, low on-state loss, and low price. However, this method adds a high-frequency current, which deteriorates the magnetic field between the poles of the interrupter when the arc is broken. Therefore, the development of HVdc circuit breakers that maintain high peak magnetic fields and low residual magnetic fields at high frequencies has become the key to the development of multiterminal HVdc transmission. To solve this problem, this article proposes a new interrupter for a vacuum dc circuit breaker based on artificial zero-crossing technology and studies its key characteristics, such as temperature rise, electromagnetic field, and arc column plasma distribution characteristics. The results reveal that the new interrupter proposed in this article has a low-temperature rise, uniformly distributed electric field, high peak value and low remanence of the longitudinal magnetic field, and uniformly distributed plasma in the arc column, and exhibits arc diffusion. Its ability to cope with high-frequency current is significantly higher than that of the traditional cup-shaped axial magnetic field (AMF) contact system interrupter, which is conducive to the high-speed and stable breaking of the interrupter.
21 November 2024 in Journal of Physics D: Applied Physics
In this paper, a three-dimensional cathode spot erosion model is proposed to study the development of cathode spot motion process on the surface of copper cathode. The formation and development process of cathode spots motion without external magnetic field is studied. In this model, energy flux density, pressure, and current value are considered as external parameters. The simulation results compared the cathode spot ablation trajectories and temperature distribution under different motion forms and motion velocities. The results indicated that during the spots expansion process, the flow of liquid metal will form a convex structure on the surface of the cathode and a hollow structure inside the cathode. Comparing different motion types, the annular motion significantly increased the roughness of the cathode surface. With the increase of the speed of spots movement, the interaction between the craters is significantly weakened, which will reduce the temperature and the roughness of the cathode surface. The simulation results are consistent with the experimental results.
This paper established a three-dimensional transient MHD model of a high-current multi-component vacuum arc under a transverse magnetic field (TMF) to simulate the dynamic characteristics of plasma parameters in the uniform motion mode of a contracted arc under lower TMF. The model considered the ionization–recombination process among the multi-components and used the P1 model to calculate the thermal radiation losses. The simulation results show that the ion number density of The TMF arc is on the order 1024 m−3, and when the plasma temperature reaches 4.3 eV, the effects of thermal radiation cannot be ignored. The majority of the plasma from the cathode and anode undergo acceleration and then deceleration before finally intersecting at the center of the arc, creating an extreme value of the density and the pressure, where a large amount of kinetic energy is converted into internal energy. The arc will be bent and deflected under the action of the ampere force, and the deflection of Cu3+ is especially obvious. The TMF affects the collision strength of the jet in the intersection area and, thus, affects the ion density, in which the change of Cu2+ is dominant. The ionization–recombination process of ions is mainly determined by the electron temperature, which is affected by the arc current. As the current decreases, Cu1+ increases and Cu2+ and Cu3+ decrease, and the change in ionization rate is the main reason for the change in the proportion of each ionic component; the heat flux density to the anode and cathode is on the order of 1010 W/m2, which heats the front of the arc and ensures the stable movement of the arc. Meanwhile, due to the high ion number density, the ion heat flux accounts for the main part of the heat flux, and the anode exhibits a higher proportion of ion heat flux.
In practical arc ignition processes of high-current vacuum arcs, despite the calibration effect of the axial magnetic field, the strong magnetic constriction force still causes the arc to contract. Additionally, during the actual electrode opening process, due to the random nature of the arcing position, the center of the arc column is often not located at the center of the electrode. At this point, the behavior of the vacuum arc can be understood as an asymmetric three-dimensional (3D) process under the influence of the spatial magnetic field, affecting the generation of anode vapor and the characteristics of arc species. Therefore, it is useful to conduct simulation studies on multi-species vacuum arc behavior considering arc contraction and arc deflection. In this paper, the spatial magnetic field distribution under different electrode effective areas and different arc center deflection distances have been simulated, and the influence of actual magnetic field-induced by arc contraction and deflection on 3D spatial distribution characteristics of arc plasma has been studied based on a 3D multi-species (CuCr alloys) vacuum arc model with anode vapor. The simulation results show that with the contraction of the arc column, the area occupied by neutral atomic vapor decreases correspondingly, but the ionization and recombination process between the arc column regions becomes more intense. The axial current density and electron temperature distribution around the neutral atomic vapor area become more non-uniform. When the arc column deviates from electrode center, the neutral atomic vapor area shows an asymmetrical distribution on both sides of the arc column center axis, and the axial current density and electron temperature gather and enhance in the opposite direction of the arc deflection, thereby significantly affecting the distribution of arc species.
28 May 2026 in IEEE Transactions on Plasma Science
During the breaking process of vacuum circuit breakers, the arc will cause the anode to heat up and melt. This will have a negative impact on the circuit breaker and reduce its life. In this study, a 3-D transient model is established to simulate the interaction between arc and anode. The process of electrode melting under arc heating and electrode evaporation affecting the arc is considered. In this study, an axial magnetic field (AMF) contact made of copper-chromium alloy with a diameter of 41mm was used. The gap distance is 10mm and the current has a root mean square (rms) value of 15kA. This study takes CuCr30material as the main research object. The simulation results show that the CuCr30electrode is heated up under the action of the arc and reaches the maximum value at 6.6ms, accompanied by an erosion depth of about $120~\mu $ m. Moreover, the overall erosion region exhibits a hexagonal distribution under the influence of the arc plasma. The comparison between CuCr10, CuCr30, and CuCr50material electrodes shows that the higher the chromium content, the higher the anode temperature, but the lower the degree of erosion. The temperature rise of the electrode also affected the arc column, leading to an active anode phenomenon. Overall, the phenomena observed in the simulation are in good agreement with the experimental observations.