1 November 2003 in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
27 August 2012 in Journal of Microelectromechanical Systems
As a novel approach to future microrobotic locomotion, a multi-degree-of-freedom (m-DoF) microrobotic appendage is presented that generates large range of motion (5° -40°) in multiple axes using thin-film lead zirconate titanate (PZT) actuators. Due to the high driving force of PZT thin films and a robust fabrication process, m-DoF legs that retain acceptable payload capacity ( ~ 2 mg per leg) are achieved. The fabrication process permits thin-film PZT actuator integration with more complex higher aspect ratio silicon structures than previous related processes, using vertical silicon dioxide barrier trenches formed before PZT deposition to provide robust encapsulation of the silicon during later XeF2 release. Planarization of the barrier trenches avoids detrimental effects on piezoelectric performance from the substrate alteration. Once fabricated, kinematic modeling of compact PZT actuator arrays in prototype leg joints is compared to experimental displacement measurements, demonstrating that piezoelectric actuator and assembled robot leg joint performance can be accurately predicted given certain knowledge of PZT properties and residual stress. Resonant frequencies, associated weight bearing, and power consumption are also obtained.
5 November 2013 in IEEE Transactions on Nuclear Science
This paper investigates total ionizing dose (TID) effects on the piezoelectric properties of lead zirconate titanate (PZT). The capacitance and contact voltage of thin-film, PZT-based relays were measured following incremental 60Co TID irradiations. The devices were held in several different bias conditions, during exposure. The direction of the biasing electric field during exposure, along with the polarization prior to exposure, has a measurable impact on post-irradiation operating voltage of the relay. In all cases, the switching voltage, as obtained via the peak values in a capacitance versus voltage sweep, shifted in a direction that would minimize the switching electric field in the direction of pre-exposure polarization. These effects were observed to be both significantly greater than the shifts experienced by a set of control samples, as well as reversible via aging at room temperature. The devices display remarkable robustness, operating during active TID exposure [dose rate = 855.6 rad(Si)/s], failing at a TID greater than 15 Mrad(Si).
23 July 2010 in IEEE/ASME Transactions on Mechatronics
A novel open-loop minimal energy on-off servo system and control strategy are described for ensuring specified displacements from new microscale piezoelectric rotational joints under extremely strict power budgets. The rotational joints are driven by thin-film lead-zirconate-titanate actuators and are targeted for use in autonomous terrestrial microrobots. A lumped-parameter, second-order model of anticipated joint behavior is utilized to estimate the natural frequency and damping ratio of the robot joints, which, in turn, are used to identify necessary sampling rates and switching drive circuit parameters for implementation of on-off control. An identified model of leg joint behavior is then used to both verify lumped-parameter modeling and to optimize on-off input sequences to the rotary joint. The optimization procedure incorporates energy costs from both switching and holding an input voltage on microactuators that behave as a capacitive load, while ensuring that specified final states of a dynamic system are achieved at a specified point in time. Optimization is done via a new application of binary programming. In addition, modest robustness of the system response to parameter variation can be produced during control sequence generation. Optimized input sequences are applied to both macroscale piezoelectric actuators and to prototype thin-film piezoelectric leg joints, and show that specified actuator motions can be achieved with energy consumption of less than 5 μJ per movement.
10 February 2012 in IEEE Transactions on Components, Packaging and Manufacturing Technology
This paper presents an X-band two-bit phase shifter that integrates single-pole four-throw (SP4T) piezoelectric microelectromechanical switches with a compact 3-D passive design on a liquid crystal polymer (LCP) organic substrate. The multilayer LCP process allows a low-cost and lightweight circuit that can easily be integrated with other radio frequency front-end components, such as an antenna, at the packaging level. By routing lines onto embedded multilayers, a 22.5% reduction in area is achieved. In addition, low-loss piezoelectric SP4T switches with a 7 V actuation voltage are used to switch between different phase delays. The phase shifter exhibits a loss of 0.75 dB/bit with 2.25° average phase error at 10 GHz.