31 March 2022 in ACS Omega
The effects of various factors on NOx reduction by urea solution injection in the fuel-rich zone (UIFR) under a reducing atmosphere at high temperature were experimentally investigated in a 330 MW tangentially pulverized coal-fired boiler. The experimental results indicated that the NOx emission of the boiler could be effectively reduced by using the UIFR method, and the NOx reduction efficiency was mostly affected by the operating load of the boiler, the air distribution condition, and the boiler operating oxygen content (BOOC). The higher the load was, the larger the optimal normalized stoichiometric ratio (NSR) and the lower the NOx reduction efficiency became. As compared with the condition of conventional air distribution mode, the reducing atmosphere in the combustion zone could be enhanced under the condition of limiting air distribution (LAD) mode, which thus increased the NOx reduction efficiency of UIFR and reduced the optimal NSR value. A low BOOC could further increase the NOx reduction efficiency of UIFR. When the BOOC was, respectively, reduced to 1.71 and 1.85 vol % under 210 and 240 MW loads, the corresponding NOx reduction efficiencies of UIFR reached 45.3 and 41.3% in the LAD mode, respectively. However, the low BOOC increased the CO emission concentration, which could be avoided by the combined use of UIFR and high-velocity over-fire air. These experimental results can provide guidance for the ultra-low NOx emission of coal-fired boilers.
28 March 2024 in ACS Omega
The efficient and clean utilization of urban waste can substitute for partial fossil fuels and reduce total carbon emissions. Fuel combustion is divided into three stages. Before the fire, the fuel is put into the furnace to reach the preparation stage of the fire temperature, the combustion stage takes place after the ignition temperature is reached, and finally, the combustion is completed. This article employs numerical simulation methods to comprehensively study the effects of various factors on the combustion characteristics of waste in a mechanical grate incinerator, including the inclination angle of the front arch, fuel properties, height of the front and rear arches, air distribution methods, and speed of the grate chain rotation. The results indicate that when the rear arch angle is set at 25 degrees, the airflow distribution within the furnace is uniform and the high-temperature flue gas exhibits an ideal "L" shaped flow, achieving favorable characteristics of airflow distribution inside the furnace. With this structure, the airflow from the rear arch can adequately penetrate deep into the front arch area, thereby forming an efficient T-shaped combustion flame.
19 March 2019 in IOP Conference Series: Materials Science and Engineering
In this paper, the combustion stability and nitrogen oxides (NOx) emissions test were made in two coal-fired chain grate boilers with hot water supplies of 29MW and 46MW. The investigations aim to clarify the key characteristics of NOx emission, e.g.instability of NOx emission, temperature and gaseous components profiles and the unsteady variation of NOx emission with power level changing. Main conclusions include: 1) In the process of stable combustion, NOx emissions still have±5% fluctuations, it is not stable. 2) The furnace temperature distribution show double temperature peaks. One peak (~1500°C) is located on the burning solid-fuel surface on the chain grate, and the other (~1050°C) is ~5.6m above the arch. 3) With increasing the thermal power, NOx emission shows a dramatic increase, higher around 1.25 times, as due to the rapid adjustment of coal feeding in grate furnace. Those above show the NOx control difficulty and the proper injector location of SNCR (selective non-catalytic reaction), which is key data collected for further NOx reduction retrofits.
9 July 2019 in IOP Conference Series: Earth and Environmental Science
Low calorific value gas fuel is a general term for fuel with calorific value lower than 1500 kcal / m3, mainly derived from low calorific value gas produced in industrial production process, including blast furnace gas, refinery associated gas, gas, pyrolysis gasification of biomass, etc. However, its heat value is low and it is difficult to control stable combustion. It is generally mixed with other fuels with high heat value and is widely used in smelting, chemical industry, power generation and other fields. Therefore, it is of great significance to study the gas burner suitable for low calorific value gas. This paper summarizes the structure, working principle and technology development status of low calorific value gas burner at present, introduces some application examples of low calorific value fuel burner, and discusses the existing problems and future development trend in this respect.
1 April 2025 in Scientific Reports
This study examines the impact of sintering air volume on the characteristics of combustible lean gases (CO, H2, and CH4) in sintering flue gas. By conducting experiments using a fixed combustion test bench, we analyzed the changes in sintering negative pressure, flue gas composition, and sinter quality under various air volume conditions. The results demonstrate that an air volume of 90 m³/(m²·min) leads to a lower combustion ratio (ω(CO)/ω(CO + CO2)), indicating more efficient utilization of fuel chemical energy. Additionally, increasing the air volume per unit area reduces the sintering time. The mass fractions of CO and H2 decrease with increasing air volume, and the mass fraction of CH4 also decreases, underscoring the importance of its recovery due to its high global warming potential (28 times that of CO2). These findings provide guidance for optimizing sintering conditions to improve lean gas recovery and reduce environmental impacts.