19 March 2018 in Journal of Physics: Conference Series
Graphene Oxide (GO) has been succesfully synthesized using Hummber method from graphite powder of pencil rod. The excellent solubility of graphene oxide (GO)in water imparts its feasibilty as new filler for reinforcement hydrophilic biopolymers. In this research, the biocomposite film was fabricated from chitosan/graphene oxide. The characteristics of graphene oxide were investigated using Fourier Transform Infrared (FT-IR) and X-ray Diffraction (XRD). The results of the XRD showed graphene structur in 2θ, appeared at 9.0715°with interlayer spacing was about 9.74063Å. Preparation films with several variations of chitosan/graphene oxide was done by casting method and characterized by mechanical and morphological analysis. The mechanical properties of the tensile test in the film show that the film CS/GO (85: 15)% has the optimum Young's modulus size of 2.9 GPa compared to other variations of CS / GO film. Morphological analysis film CS/GO (85:15)% by Scanning Electron Microscopy (SEM), the obtained biocomposites film showed fine dispersion of GO in the CS matrix and could mix each other homogeneously.
1 November 2018 in Journal of Physics: Conference Series
Biomass-such as cellulose is one of the most common abundant organic materials on the Earth. Biomass has carbon chain that could be an excellent choice for the fabrication of carbon materials. Cellulose nanocrystal is nano-sized cellulose and could become the potential source in fabricating carbon nanodots that are affected by pyrolysis temperature. In fact, the size and temperature are essentially important to synthesize the carbon nanodots. This research is contributed to synthesize this material, and to investigate the effect of temperature. The percentage of cellulose nanocrystals and carbon nanodots obtained are less than 50%. Carbon nanodots are synthesized by pyrolysis method and cellulose nanocrystals are fabricated by membrane method. TEM analysis shows that cellulose nanocrystals are nano-sized. Under UV light source, the samples show fluoroscencing colours i.e. blue to green. From this research it can be concluded that the temperature affects the characteristics of carbon nanodots produced by pyrolysis method.
24 December 2018 in Journal of Physics: Conference Series
In this study, all-cellulose composite film which was fabricated by utilizing the cellulose extracted from empty brunch of palm oil has been successfully conducted. The film was initially prepared by performing chemical technique treatments involving alkaline treatments to remove the ligno-cellulosic contents. To obtain the nano-scale materials, the mechanical experiments were performed by using the homogenizer instruments, so the nanofiber cellulose could be obtained in addition to fabricate the film. Next, the cellulose fiber was partially dissolved by 8% LiCl/DMAc and it was used to fabricated composite film of all fiber cellulose. Functional groups of the cellulose fiber were characterized using FT-IR spectroscopy. The highest tensile strength was held by all fiber cellulose treated 2% NaOH, i.e 109.37 MPa, Young's Modulus 3.56 GPa, and elongation at break 3.07%. The morphology was also determined using scanning electron microscopy (SEM) and showed the most regular surface structure owned by all fiber cellulose treated 2% NaOH as well.
14 December 2018 in AIP Conference Proceedings
Oil Palm Empty Fruit Bunches (OPEFB) are abundant organic waste that contains cellulosic compound. This study aims to fabricate PCL/cellulose nanofiber bionanocomposites from OPEFB and to analyze their thermal and mechanical properties. Nanofiber cellulose with an average size of 32 nm was isolated from OPEFB by using alkaline condition and mechanicalmethods. This was proven by the presence of functional group analysed from the FT-IR spectrum and morphological analysis with TEM. Bio-nanocompositePCL/cellulose nanofiberfrom OPEFBwas further made in several variations, namely: 100%: 0%, 90%: 10%, 80%: 20%, 70%: 30%, 60%: 40%. The samples were then tested for their mechanical properties with tensile test to determine optimal results and the optimal ratio was 80%: 20% w/v, with tensile strength of about 8,830 Mpa and 40,78% strain. This is also proven by morphological analysis using SEM which shows a flat and homogeneous surface. The optimal sample was thermally analyzed using DSC and it is showed that the resulting bionanocomposite decomposed (Td) at 513.10°C through an exothermic process with a heat of 414.08 J/g.
24 December 2018 in Journal of Physics: Conference Series
This study aims to fabricate cellulose nanocomposite film from oil palm empty fruit bunches (OPEFB) and to compare the difference in resulted films, which were treated with various dissolution time. The method applied to generate cellulose fiber was steam explosion method; also, the alkali treatment was employed. In order to form cellulose nanocomposite film from cellulose nanofibers, LiCl/DMAc was used as the solvent with the dissolution time varied, namely 30 minutes and 60 minutes. The chemical structure was investigated using Fourier transform infrared (FT-IR) spectroscopy, whereas the surface morphology was done using scanning electron microscope (SEM). The FT-IR results show all appropriate vibration peaks to confirm that the cellulose nanofibers and nanocomposite film were successfully produced. From the photographs of the cellulose nanocomposite film as well as SEM photographs, it can be concluded that 60 minutes dissolution time gives smoother surface and more transparent film than those of 30 minutes.