1 November 2024 in Physics of Fluids
This paper examines the impact of scramjet isolator shape transition on hypersonic internal waverider (IWR) intake. The IWR intake is designed using the osculating axisymmetric flows and streamline-tracing methods. The new Internal Conical Flow “M” basic flowfield is utilized to provide the flow information for the design method. The intake is equipped with three isolators: one with a constant cross section and two with variable cross sections with circular and rectangular exits. The entrance shape and area of the three isolators are fixed to the intake throat shape and area. The exit area of the three isolators is maintained as the entrance one. Numerical computations of three-dimensional configurations reveal that the isolators with variable cross section shapes demonstrate a higher uniformity index than those with constant cross section shape. Thus, the isolator shape transition has decreased the flow distortion of the hypersonic IWR intake system. The three isolators exhibit varied wall pressure distribution depending on the isolator cross section shape, and the total pressure recovery ratios at the three isolators' exit planes are similar. The wall pressure distributions and key performance parameters at the intake throat section, including total pressure recovery, compression ratio, and Mach number, remained consistent across the first part of the intakes. Therefore, changing the cross section shape of the isolator while keeping the area constant could enhance the flow uniformity of compressed air without negatively impacting the intake system's performance. This allows a separate shape selection of the IWR intake throat and the scramjet combustor entrance to fulfill their special requirements.
1 May 2024 in Physics of Fluids
The current work is undertaken to examine the capability of a recently developed ICFM (internal conical flow M) basic flowfield [Musa et al., AIAA J. 61, 1–16 (2023)] to design hypersonic internal waverider intakes. The osculating axisymmetric flows concept is employed alongside the streamline-tracing method to design three internal waverider intakes with different contraction ratios, i.e., 6.0, 9.0, and 25. The three intakes have similar capture and throat shapes and entrance areas. Then, the starting characteristics of designed intakes were investigated at different design and off-design conditions. The selected design condition is the flight at Mach 6.0 and 28 km altitude. Viscous computations have been performed at Mach 6.0, 5.0, 4.0, 3.9, 3.8, 3.5, and 3.0 for the intake with a contraction ratio of 6.0, and at Mach 6.0, 5.0, 4.7, and 4.0 for the intake with contraction ratio of 9.0. The intake with a contraction ratio of 25 is simulated at Mach 6.0 and 5.0. Successful intake starting has been achieved up to Mach 3.8 for the first intake and up to Mach 4.7 for the second intake. The intake with a contraction ratio of 25 attained an unstart state in the design condition due to a very high contraction ratio. Thus, the starting limit of internal waverider intakes designed using ICFM basic flowfield is found to be controlled by Van Wie empirical limit. It is concluded that the ICFM basic flowfield can effectively design high-performance fixed-geometry intakes with overboard spillage, demonstrating excellent performance and startability across a wide range of Mach numbers.
14 May 2025 in Aerospace Science and Technology
1 September 2024 in Physics of Fluids
The current paper proposes a new third-order WENO (weighted essentially non-oscillatory) scheme, denoted as WENO-D3, which constructs the numerical flux using the convex combination of a second-degree polynomial of a three-point stencil with two linear polynomials of two substencils. WENO-D3 comes with a compact formulation of the numerical flux, new compact nonlinear weights, a new reference smoothness indicator, and a simple smoothness indicator for the three-point stencil. The forward differences approach is employed to reformulate the expressions of the polynomials and smoothness indicators of the new scheme. The smoothness indicator of the three-point stencil is designed using a linear combination of the two-point substencil smoothness indicators and compact linear weights. The linear weights of WENO-D3 can be freely selected with one condition: their sum equals one. A detailed analysis of the WENO-D3 scheme is provided, and numerous one- and two-dimensional benchmark numerical experiments are studied. Thirty-one combinations of linear weights are studied to verify the sensitivity of WENO-D3 to linear weights selection. Compared to the WENO-MZQ3 scheme, the WENO-D3 scheme significantly reduced the computational complexity and cost while providing flexibility in linear weights selection. The results show that the new scheme reduces up to 91% of the WENO-MZQ3 scheme's computational time and provides stable results for a wide range of linear weights. The results also show that the proposed scheme has recovered the optimal order at critical points and can capture and resolve sharp discontinuities without spurious oscillations.
25 October 2025 in Aerospace Science and Technology
27 June 2026 in Aerospace Science and Technology