Introducing a fluid microjet into the boundary layer to increase fluid momentum and hence delay separation is a method for actively controlling a flow separation region. The present work numerically analyzed the control of a separation bubble behind a ramp. For this purpose, we first verified the steady-state numerical results for a flow (without a jet) over the ramp against reliable experimental studies from the literature. Next, the effects of introducing a microjet to the flow were also verified. A jet was then placed at three different distances above the ramp to study its impact on various parameters, including velocities, Reynolds stresses, pressure, vorticity, streamlines, and the separation bubble size. As the jet was moved further back, the jet-induced upwash region grew considerably. Finally, the effects of using three identical jets were studied and compared against those of a single jet. The results indicated that using a three-jet array shrank the separation bubble. Using an array with d/D = 15 (distance between microjets over microjet diameter) can limit laterally the separation bubble about 2.75 times smaller than a single jet in the z-direction. Also, the employment of the jet managed to decrease the length of the separation zone in the x-direction up to 78%, in the case of Lx/L1 = 0.0143 (longitudinal distance of microjet from above the ramp over ramp length) and d/D = 10.
Experimental and numerical analysis of active and passive flow control is an important topic of practical value in the study of turbulent flows. This paper numerically analyzed the effects of an air microjet on an adverse pressure gradient turbulent boundary layer over a flat plane. Experimental data were employed to verify the numerical modeling. Vortex formation and development were then studied by changing the microjet to inflow velocity ratio (VR) and microjet angles. According to the results, the best values of the angles and for various velocities were found to be 30° and from 60° to 90°, respectively. Moreover, at VRs = 1, 2, and 4, the values (the distance at which the complete vortex persisted in the flow) were 0.058, 0.078, and 0.18, respectively. Compared to VR = 1, the vortex strength for VRs = 2 and 4 grew by 3.5 and 6.8 times, respectively. When the microjet was added to the flow, the highest variation in the Reynolds stress along the x-direction from VR = 1–4 was 10%. The corresponding values along the y and z- directions were 15% and 2.7 times, respectively.
The present work studied various models for predicting turbulence in the problem of injecting a fluid microjet into the boundary layer of a turbulent flow. For this purpose, the one-equation Spalart–Allmaras (SA), two-equation k–ε and k–ω, multi-equation transition k-kL–ω, transition shear stress transport (SST), and Reynolds stress models were used for solving the steady microjet into the turbulent boundary layer, and their results are compared with experimental results. Comparing the results indicated that the steady solution methods performed sufficiently we for this problem. Furthermore, it was found that the four-equation transition SST model was the most accurate method for predicting turbulence in this problem. This model predicted the velocity along the x-axis in near- and far-jet locations with about 1% and 5% average errors, respectively. It also outperformed the other methods in predicting Reynolds stresses, especially at the center (nearly 5% error). Moreover, the modified four-equation transition SST model has improved the system's performance in predicting the studied parameters by utilizing Sørensen correlations in predicting Reθt (the transition momentum thickness Reynolds number), Flength (an empirical correlation that controls the length of the transition region), and Reθc (the critical Reynolds number where the intermittency first starts to increase in the boundary layer).
The current work is undertaken to examine the capability of a recently developed ICFM (internal conical flow M) basic flowfield [Musa et al., AIAA J. 61, 1–16 (2023)] to design hypersonic internal waverider intakes. The osculating axisymmetric flows concept is employed alongside the streamline-tracing method to design three internal waverider intakes with different contraction ratios, i.e., 6.0, 9.0, and 25. The three intakes have similar capture and throat shapes and entrance areas. Then, the starting characteristics of designed intakes were investigated at different design and off-design conditions. The selected design condition is the flight at Mach 6.0 and 28 km altitude. Viscous computations have been performed at Mach 6.0, 5.0, 4.0, 3.9, 3.8, 3.5, and 3.0 for the intake with a contraction ratio of 6.0, and at Mach 6.0, 5.0, 4.7, and 4.0 for the intake with contraction ratio of 9.0. The intake with a contraction ratio of 25 is simulated at Mach 6.0 and 5.0. Successful intake starting has been achieved up to Mach 3.8 for the first intake and up to Mach 4.7 for the second intake. The intake with a contraction ratio of 25 attained an unstart state in the design condition due to a very high contraction ratio. Thus, the starting limit of internal waverider intakes designed using ICFM basic flowfield is found to be controlled by Van Wie empirical limit. It is concluded that the ICFM basic flowfield can effectively design high-performance fixed-geometry intakes with overboard spillage, demonstrating excellent performance and startability across a wide range of Mach numbers.
The present work studied various models for predicting turbulence in the problem of injecting a fluid microjet into the boundary layer of a turbulent flow. For this purpose, the one-equation Spalart-Allmaras (SA), two-equation k-ε and k-ω, multi-equation transition k-kL-ω, transition shear stress transport (SST), and Reynolds stress models were used for solving the steady microjet into the turbulent boundary layer, and their results are compared with experimental results. A comparison of the results indicated that the steady solution methods performed sufficiently well for this problem. Furthermore, it was found that the four-equation transition SST model was the most accurate method for predicting turbulence in this problem. This model predicted the velocity along the x-axis in near- and far-jet locations with about 1% and 5% errors, respectively. It also outperformed the other methods in predicting Reynolds stresses, especially at the center (nearly 5% error). Moreover, the modified four-equation transition SST model has improved the system’s performance in predicting the studied parameters by utilizing Sørensen correlations in predicting 𝑅𝑒???????? (the transition momentum thickness Reynolds number), 𝐹????ength (an empirical correlation that controls the length of the transition region), and 𝑅𝑒𝜃𝑐 (the critical Reynolds number where the intermittency first starts to increase in the boundary layer).