In this letter, a newly dual-mode composite right-/left-handed (CRLH) resonator with fully symmetrical structure is proposed to design high-order high-temperature superconducting (HTS) dual-band differential bandpass filter (BPF). Based on the conventional CRLH unit cell, a dual-mode symmetrical CRLH resonator is developed for constructing dual-band differential BPF. The resonant properties of the proposed dual-mode resonator are investigated by building differential-mode (DM) and common-mode (CM) equivalent circuits (ECs) and their lumped ECs (LECs). Finally, a fourth-order dual-band HTS differential BPF with two DM passbands that operate at 2.45 and 4.94 GHz is designed. Good agreement between the simulated and measured results validates the proposed structure and the design method.
10 January 2025 in IEEE Antennas and Wireless Propagation Letters
A uniplanar quasi-isotropic folded dipole is proposed by using a hybrid genetic algorithm and particle swarm optimization (GA-PSO) algorithm. The proposed antenna is evolved from a half-wave dipole, where the dipole is folded to achieve a pair of out-of-phase line sources and an orthogonal line source, thereby obtaining a quasi-isotropic radiation pattern. Based on GA-PSO algorithm, the bending position is optimized for the minimum gain difference. For demonstration, the dipole prototype operating at 915 MHz is designed and fabricated in which a parallel transmission line with comb-like structure is adopted to achieve good impedance matching. The measured result shows a gain difference of 2.81 dB, and the simulated value is 0.34 dB. Compared with other quasi-isotropic antennas, the proposed antenna has merits of simple structure, low gain difference and uniplanar structure.
Two types of short-circuited stub-embedded ring resonators (SERRs) are proposed in this paper. The resonant modes of the SERR can be designed by properly choosing the short-circuited point on the resonator. When the short-circuited point is set at the open-end of embedded-stub, type A resonator is realized and large frequency ratio of harmonic to fundamental frequency can be achieved. Simultaneously, wide stopband can be realized. When the short-circuited point is set at the loop portion of SERR, type B resonator is realized and low frequency ratio of harmonic to fundamental frequency can be achieved. These characteristics of the resonators type A and type B are explored and combined in a diplexer with common resonator part. Each channel of the diplexer are constructed by using the type A resonators for wide stopband, and then combined via a type B resonator for designated frequencies. A third-order diplexer operating at 3.45/5.8 GHz for fifth generation of mobile communications (5G) and wireless local area networks (WLAN) is designed, fabricated, and measured. Measured results agree well with the simulated ones, which confirms the proposed design methodology.
19 October 2023 in Journal of Physics D: Applied Physics
In this article, a newly spoof surface plasmon polaritons (SSPPs) is proposed and used to design a compact wideband bandpass filter (BPF). Different from the traditional SSPP unit cell with one-shaped structure, the unit cell of the proposed SSPPs consists of an H-shaped slotline and a bilateral T-shaped slotline. Benefiting from the hybrid structure, no transition portion is needed for impedance matching in the design of the microwave filter, which highly reduces the horizontal size of the SSPPs-based filter. The transition structure of microstrip to slotline provides a capacitance with a highpass frequency response, which enables the realization of a passband by cooperating with the natural lowpass property of SSPPs. Also, the upper and lower cutoff frequencies of the proposed filter can be adjusted independently by the key parameters. Besides, a wide upper stopband can be obtained by properly designing the SSPPs unit cell and the microstrip to slotline structure. Finally, a well-designed BPF operated at 1.3–6.2 GHz and its upper stopband rejection reaching 20 GHz is fabricated and measured. The test results are in good agreement with the simulations, which verifies the feasibility of the proposed structure and design method.
13 September 2023 in IEEE Transactions on Applied Superconductivity
In this paper, a compact high temperature superconducting (HTS) fourth-order tri-band balanced bandpass filter (BPF) is developed by using a newly proposed multi-mode symmetric stub-loaded resonator (SSLR). The differential-mode (DM) and common-mode (CM) resonance characteristics of the SSLR are analyzed based on the transmission line theory and even-/odd-mode method. Then, the configuration and coupling topology of a fourth-order tri-band balanced BPF are proposed, and variations behaviors of the design parameters versus the structural dimensions of the filter are investigated. Finally, the tri-band balanced BPF operating at 1.56/4.22/5.8 GHz is designed and fabricated using HTS YBCO films deposited on an MgO substrate. The measured filter response agrees well with the simulated one, and shows excellent properties like low insertion loss, high frequency selectivity, and larger CM suppression.
7 November 2022 in IEEE Microwave and Wireless Technology Letters
A novel coupling scheme is proposed based on short-circuited stub-embedded resonator (SCSER) for bandpass filters (BPFs). The BPF utilizing SCSER owns three transmission zeros (TZs) that are controlled by short-circuited and open-circuited stubs. Based on the proposed SCSER and coupling structure, a novel high-isolation diplexer is presented. When the TZ is allocated in the opposite channel and impedance transformation is carried out in the common port, the proposed diplexer can be realized by directly combining two different BPFs without an additional matching network. For the demonstration, a BPF and a diplexer based on SCSER are fabricated and measured. The measured results agree well with the simulated ones.