This research targets disentangling shallow causes of anthropogenically induced subsidence in a reclaimed and urbanized coastal plain. The study area is the city of Almere, in the South Flevoland polder, the Netherlands, which is among the countries' fastest subsiding areas. The procedure consists of integrating Interferometric Synthetic Aperture Radar (InSAR) data with high‐resolution phreatic groundwater and lithoclass models, and a database containing construction details. The InSAR data were derived from Sentinel‐1, one ascending and one descending track, over a period from March 2015 until June 2020. The two main parts of the workflow are isolation of the InSAR points of structures without a pile foundation and a data assimilation procedure. The shrinkage of surficial clay beds by phreatic groundwater level lowering is identified as the main cause of subsidence in the area, with an average contribution of 6 mm per year. The history‐matched physics‐based model predicts that 1 m drop in phreatic groundwater level now translates into 10 mm of subsidence in the next 5 years. Additionally, a groundwater deficiency due to severe dry periods should be considered as an accelerator of subsidence. To ensure a robust network to estimate subsidence, we recommend a consistent monitoring strategy of the phreatic groundwater level.
This research targets disentangling shallow causes of anthropogenically-induced subsidence in a reclaimed and urbanized coastal plain. The study area is around the city of Almere, in the South Flevoland polder, the Netherlands, which is among the countries’ fastest subsiding areas. The procedure consists of integrating synthetic Interferometric Synthetic Aperture Radar (InSAR) data with high-resolution phreatic groundwater and lithoclass models, and a database containing construction details. The two main parts of the workflow are isolation of the InSAR points of structures without a pile foundation and a data assimilation procedure by Ensemble Smoothing with Multiple Data Assimilation. The shrinkage of surficial clay beds by phreatic groundwater level lowering is identified to be the main cause of shallow subsidence in the area, with an average contribution of 6 mm/year. The history-matched physics-based model predicts that one meter drop in phreatic groundwater level now translates into 10 millimeter of subsidence in the next five years. Also, this study showed that a groundwater deficiency due to severe dry periods should be considered as an accelerator of subsidence in both the short- and long-term planning. To ensure a robust network to estimate future subsidence, we advise on a consistent monitoring strategy of the phreatic groundwater level.
The open-source Python package Geoloop introduces a novel, semi-analytical model for predicting the performance of deep (>500 m depth) vertical borehole heat exchangers (BHEs), with a focus on capturing depth-dependent variations in subsurface thermal properties, i.e., geothermal gradient and thermal conductivity. Conventional computationally efficient semi-analytical models based on load-aggregation of g-functions often assume uniform subsurface thermal properties. Geoloop addresses this gap by implementing a vertically stacked approach, allowing for realistic simulation of depth-variability in both the subsurface and borehole material properties. The model is benchmarked in the shallow domain against standard depth-uniform g-function implementations (up to 100 m depth) and for deeper conditions with a numerical finite volume model, demonstrating strong agreement and validating its accuracy and efficiency. Simulations for typical Dutch conditions show that deeper BHEs (up to 2000 m) can achieve significantly higher thermal power supply than shallower systems, and results in terms of resulting inlet/outlet temperatures for given heat extraction rates can strongly deviate (>4 °C) from results obtained by depth-uniform assumptions in thermal properties. Application of the model to the Dutch context reveals a non-linear increase in heat extraction potential with depth, surpassing values assumed in common practice by Dutch industry. The results highlight the importance of considering local geological heterogeneity and depth-dependent properties for accurate deep borehole heat exchanger (BHE) performance assessment and system optimization. Geoloop thus offers a robust, versatile platform for advancing the design and analysis of deep vertical BHE systems.
Usually, subsoil data for groundwater models are generated from borehole data, using upscaling techniques. Since the assumed hydraulic properties for litho-classes in boreholes are uncertain, and upscaling may add inaccuracies, the groundwater model has to be calibrated. In this paper, a method is presented that uses a calibrated groundwater model to improve the quality of a hydrogeological model (layer thickness and hydraulic properties) as obtained from borehole data. To achieve this, all borehole data are defined by random variables and related to aquifer and aquitard properties at the same support as the groundwater model, using complete probability density functions. Subsequently, the calibrated parameter values of the groundwater model are assumed to be the truth and are used to find the most likely combination of layer thicknesses and hydraulic conductivities for the lithological layers making up the aquifer or aquitard. The presented example is an application of the proposed method to aquitards. Nevertheless, the method can be applied to aquifers as well. The analysis of the results gives rise to the discussion about the correctness of the hydrogeological interpretation of the borehole data as well as the correctness of the calibration results of the groundwater flow model. In order to make the problem tractable, computationally feasible, and avoid assumptions about the distribution form, piecewise linear probability density functions are used, instead of parametrized functions.