6 July 2020 in IEEE Access
This paper proposes a new interleaved non-isolated high step-up dc-dc converter for interfacing renewable energy applications. The proposed converter achieves a very high step-up voltage gain by using two coupled inductors and a voltage multiplier cell. This topology utilizes the interleaved boost converter in the input side, and the input current is shared with low ripple. Moreover, a voltage multiplier cell with the secondary windings of the coupled inductors is employed in the output side to achieve the interleaved energy storage. The voltage stress on the semiconductor switches and the passive components is significantly reduced and lower than the output voltage. The aforementioned converter can be operated without an extreme duty cycle or a high turns ratio. The reverse recovery problem of the diodes is mitigated, and the leakage energy is recycled. Furthermore, by implementing low-voltage-rated MOSFETs with a small ON-resistance, the conduction losses can be reduced, and the efficiency can be improved. The topology is fed by a single input voltage, and the mathematical expression is methodically explored. The operation principle of the proposed converter and the comparison between the proposed converter with other topologies are discussed. The design, parameters selection, and experimental results are thoroughly introduced. A 32 to 800 V-dc is verified and simulated by using PLECS. Consequently, a 400 W hardware prototype is verified to validate the theory and the design.
15 January 2001 in Journal of Applied Physics
Simulations have been performed to determine the internal temperature profiles of high-power GaAs photoconductive switches in the presence of a current filament. No thermal instability is predicted below a power generation density level of about This prediction is in keeping with recent experimental data on photoconductive semiconductor switch devices. It is shown that this power dissipation density threshold for stability exists under both dc and transient conditions. A simple model provides qualitative support for the power density threshold, and an explanation of the filamentary current radii that have been observed experimentally.
19 April 2018 in Canadian Journal of Electrical and Computer Engineering
An in-depth analysis of signals from horn antennas used in breast cancer detection research has been carried out. It was found that following the excitation signal, both the double-ridged and the quad-ridged ultra-wideband horn antennas radiate additional unwanted signals that persistently oscillate. Undesirable signal oscillations sources were identified as the horn antenna cavity resonance and inherent antenna LC resonance. These signals interfere with the tumor's signal response and need to be eliminated for successful detection of the cancerous growth. This paper proposes solutions to remove or minimize these signals without affecting antenna parameters such as bandwidth, gain, ports isolation, and polarization isolation. Modification of the antenna cavity successfully suppressed the unwanted cavity oscillation. Modification of the antenna waveguide reduced inductance and consequently mitigated LC oscillation. The resulting time and frequency domain horn antenna signals demonstrate the effectiveness of the proposed methods. Finally, a breast phantom with a tumor is simulated using signals from the original and a modified horn antenna. The delay and sum method is used to create images. The breast images demonstrate enhanced image quality through the reduction of clutter using the proposed techniques. The signal-to-clutter ratios are 0.448 and 1.6823 dB for the images produced by using the original and modified antennas, respectively.
21 November 2008 in IEEE Electron Device Letters
A methodology to compute tunneling currents in a nanocrystal (NC) memory cell is presented to reveal the positive impact of using metal NCs as storage nodes. An analytical model for quantifying the NC effect on electrostatic potential has been used with a transmission line analogy-based quantum mechanical method to calculate the tunneling current. The model includes the effects of the electron wave function penetration into the gate dielectric and also shows the influence of NCs' spacing and material properties on the programming characteristic of the memory cell. Results can be used in optimizing the structure for maximum programming efficiency.
15 July 2007 in Journal of Applied Physics
A modified electromagnetic topology (EMT) simulation scheme for the interactions of an electromagnetic wave with an aperture and with cables of an electrical system beyond the aperture is described. The modified EMT simulation scheme addresses a concept in dealing with an aperture node of the topological circuitry without having to specify the details of the entire electrical circuitry. The results of the modified EMT simulation scheme have been validated through experiments for aperture∕wave interactions and the induced currents on the cable near the aperture. The aperture transfer functions, obtained for both the simulation and experimental cases, have shown the characteristic response similar to that of the high-pass filter with a cutoff frequency. The simulated and measured currents on a cable, placed behind the aperture, resulted in good agreement with each other, providing the good validation of the modified EMT simulation scheme. Under this scheme, any change in topological circuitry can be handled easily in the substructural levels without having to consider an entire system. Consequently, the effects of various types of aperture interactions on the entire system can be reinvestigated via simply remodeling of topological interaction nodes in substructural levels.
2 July 2007 in IEEE Antennas and Wireless Propagation Letters
A new approach to perform electromagnetic topology based simulation is proposed by incorporating a modular scattering junction concept. This method substitutes the multistep computation technique presented earlier and is convenient to implement. The method also allows for incorporating substructural modifications without repeating solutions to the entire system. The simulation of the overall interaction utilizes transmission-line matrix compaction, finite-difference time-domain method, and reciprocity theorem to create different junctions. Results are compared with experiments conducted in the laboratory. A good agreement is shown for the simulated and experimental data.