This paper proposes a new interleaved non-isolated high step-up dc-dc converter for interfacing renewable energy applications. The proposed converter achieves a very high step-up voltage gain by using two coupled inductors and a voltage multiplier cell. This topology utilizes the interleaved boost converter in the input side, and the input current is shared with low ripple. Moreover, a voltage multiplier cell with the secondary windings of the coupled inductors is employed in the output side to achieve the interleaved energy storage. The voltage stress on the semiconductor switches and the passive components is significantly reduced and lower than the output voltage. The aforementioned converter can be operated without an extreme duty cycle or a high turns ratio. The reverse recovery problem of the diodes is mitigated, and the leakage energy is recycled. Furthermore, by implementing low-voltage-rated MOSFETs with a small ON-resistance, the conduction losses can be reduced, and the efficiency can be improved. The topology is fed by a single input voltage, and the mathematical expression is methodically explored. The operation principle of the proposed converter and the comparison between the proposed converter with other topologies are discussed. The design, parameters selection, and experimental results are thoroughly introduced. A 32 to 800 V-dc is verified and simulated by using PLECS. Consequently, a 400 W hardware prototype is verified to validate the theory and the design.

High gain dc-dc converters are used in several applications which include solar photovoltaic system, switch-mode power supplies and fuel cells. In this paper, an ultra-high gain dc-dc boost converter is proposed and analyzed in detail. The converter has a gain of six times as compared with the boost converter. The high gain is achieved by utilizing switched inductors and switched capacitors. A modified voltage multiplier cell (VMC) with switched inductors is proposed. The converter has a single switch which makes its operation easy. Moreover, the voltage across the switch, diodes and capacitors are less than the output voltage which increases the overall efficiency of the converter. The converter performance in steady-state is analyzed in detail and it is compared with other latest high gain converters. The working of the converter in non-ideal conditions is also discussed in detail. The loss analysis is done using PLECS software by incorporating the real models of switches and diodes from the datasheet. To confirm and validate the working of the proposed converter a hardware prototype of 200 W is developed in the laboratory. The converter achieves high gain at low duty ratios and its performance is found to be good in open and closed loop conditions.

This paper introduces the concept of inductors asymmetric input voltage to derive a new high voltage gain converter. The proposed converter has continuous input, positive output, and high-power density features suitable for renewable energy applications. The operating principle, steady-state performance, practical voltage gain, small-signal analysis, and efficiency of the converter are presented in this work. A comprehensive comparison is made with the high voltage gain converters available in literature in terms of component count, voltage gain, effectiveness index, voltage and current stress on the power devices, per unit switching device rating, and other features like output polarity and availability of common ground. The proposed topology possesses a higher effectiveness index and lower switching device power rating (SDP), resulting in a good form factor. To validate the performance of the proposed converter, the experiments are conducted on the 150 W laboratory prototype, and corresponding results are presented in this work.

This work has adopted the concept of asymmetric inductor magnetization to develop a new quadratic converter with the advantages like a wide range quadratic voltage gain and low source current ripple. In addition, the proposed high quadratic converter has achieved reduced voltage stress due to the presence of switched capacitor cell at the output side. Initially, the operation of the converter and steady-state analysis, including efficiency calculations, are explained. In addition, the design and selection of converter components are presented along with a small-signal analysis. Further, a comprehensive comparison with recent high quadratic gain converters is presented. The comparison is made with regard to the total component count, voltage conversion ratio, effectiveness index, electric stress, current ripple, switching device power (SDP) rating, and input current ripple factor. Furthermore, the 150 W laboratory prototype is used to verify the performance of the proposed converter in terms of operation, dynamic response, and efficiency, and the corresponding experimental findings are reported. The wide range voltage gain, low current ripple, and low electric stress features of the proposed converter highlight its superiority in fuel cell electric vehicle applications.

This research paper presents a novel approach to current control in Grid-Connected Inverters (GCI) using Deep Reinforcement Learning (DRL) based Twin Delayed Deep Deterministic Policy Gradient (TD3) method. The study focuses on addressing the limitations of traditional control techniques and state of the art techniques, particularly Proportional-Integral (PI) control and Model Predictive Control (MPC), by leveraging the adaptive and autonomous learning capabilities of DRL. The proposed novel modified TD3-based DRL method learns an optimal control policy directly from raw data, enabling the controller to adapt and improve its performance in real-time. The research includes a comprehensive analysis of the implementation and validation of the modified TD3-based DRL control in a grid-connected three phase three level Neutral Point Clamped (NPC) inverter system with Inductor-Capacitor-Inductor (LCL) filter. Real-time validation experiments are conducted to evaluate the control performance, power transfer capability in grid compliance. Furthermore, a detailed comparison is presented with experimentation, highlighting the advantages of the TD3-based DRL control over PI and MPC control techniques. Robustness checking is performed under various operating conditions, including parameter variations and dynamic conditions in the grid. The results analysis demonstrates that the TD3-based DRL control outperforms traditional PI control techniques in terms of static, dynamic response, and robustness. Additionally, The DRL based grid connected inverter current control method is validated in Renewable Energy Source (RES) solar PV grid integration application.