2 February 2022 in IEEE Transactions on Applied Superconductivity
Next generation ion therapy magnets both for gantry and for accelerator (synchrotron) are under investigation in a recently launched European collaboration that, in the frame of the European H2020 HITRI plus and I.FAST programmes, has obtained some funding for work packages on superconducting magnets. Design and technology of superconducting magnets will be developed for ion therapy synchrotron and -especially- gantry, taking as reference beams of 430 MeV/nucleon ions (C-ions) with 10 10 ions/pulse. The magnets are about 60–90 mm diameter, 4 to 5 T peak field with a field change of about 0.3 T/s and good field quality. The paper will illustrate the organization of the collaboration and the technical program. Various superconductor options (LTS, MgB 2 or HTS) and different magnet shapes, like classical CosTheta or innovative Canted CosTheta (CCT), with curved multifunction (dipole and quadrupole), are under evaluation, CCT being the baseline. These studies should provide design inputs for a new superconducting gantry design for existing facilities and, on a longer time scale, for a brand-new hadron therapy centre to be placed in the South East Europe (SEEIIST project).
1 September 2023 in Physical Review Accelerators and Beams
Following the spectacular success of the third-generation light source over the past decades, a few new-generation light sources based on the multibend achromat (MBA) scheme have come into operation. Other such facilities are also under construction while existing ones are being upgraded. Likewise, the Swiss Light Source, which has been in operation for more than 20 years at the Paul Scherrer Institute, is to be upgraded with the present storage ring being replaced by an MBA low-emittance ring. A natural emittance of 158 pm at a beam energy of 2.7 GeV is achieved for a storage ring of comparatively short circumference, 288 m, providing a gross straight section of 83.6 m. The objectives of the upgrade were met under tight constraints by the application of two novel concepts: the introduction of both a longitudinal gradient and a reverse bend into the unit cell and pushing the superperiodicity to the number of arcs, effectively with “pseudosymmetry.” A detailed account of the MBA design and its expected performance is presented and the experience gained is highlighted with the aim to facilitate next-generation light source lattice design.
6 June 2025 in The European Physical Journal C
Electric dipole moments (EDM) of fundamental particles inherently violate time-reversal (T) and the combined charge-conjugation and parity symmetry (CP). We aim to measure the EDM of the muon using the frozen-spin technique within a compact storage trap. This method exploits the high effective electric field, $$E\approx {165\,\mathrm{MV/m}}$$ , experienced in the rest frame of the muon with a momentum of about $${23\,\mathrm{MeV/}}c$$ when it passes through a solenoidal magnetic field of $$|\vec {B}|={2.5\,\textrm{T}}$$ . In this paper, we outline the fundamental considerations for a muon EDM search and present a conceptual design for a demonstration experiment to be conducted at secondary muon beamlines of the Paul Scherrer Institute in Switzerland. In Phase I, with an anticipated data acquisition period of 200 days, the expected sensitivity to a muon EDM is $$\sigma (d)\le {4E-21\,\mathrm{{\text {e}}\!\cdot \!\text {cm}}}$$ . In a subsequent phase, Phase II, we propose to improve the sensitivity to $$\sigma (d)\le {6E-23\,\mathrm{{\text {e}}\!\cdot \!\text {cm}}}$$ using a dedicated instrument installed on a different beamline that produces muons of momentum 125 $$\textrm{MeV}\!/\!{ c}$$ .
12 November 2013 in IEEE Transactions on Applied Superconductivity
The knowledge of the thermal strain distribution of the Nb 3 Sn filaments in a cable in conduit conductor (CICC) cross section is a key parameter in understanding the cable performance evolution when it undergoes electromagnetic (EM) cyclic loading. A CICC is a complex system and as such it behaves in a way that is not directly predictable by studying the single components. Reversible and irreversible phenomena occur together; therefore, the explanation of the observed CICC properties is not straightforward. The magnetic susceptibility measurements, via an appropriate data reduction, allow to quantify the thermal strain. Several ITER toroidal field (TF) and central solenoid (CS) samples have been measured with this technique in the SULTAN test facility. Each cable behaves differently from the others; however, it is possible to identify common features. For some samples, the evolution of the performance with the EM cycles is dominated by the change of the strain distribution during the EM load; for others, also the irreversible phenomena play an important role. The magnetic measurements have been used in this paper to analyze the performance of several CICCs.
18 February 2025 in IEEE Transactions on Applied Superconductivity
In recent years, particle accelerator facilities have become more aware of the sustainability of their scientific research activity investing in new energy-efficient technologies and energy management of their infrastructure. To address this issue, focusing on medium- to high-energy range proton and heavy ion beamlines, a growing interest in using superconducting magnets instead of energy-demanding resistive configurations has been observed. The proposed study, conducted by the research team from the University of Milan and the Istituto Nazionale di Fisica Nucleare (INFN), Milano, Laboratorio di Acceleratori e Superconduttività Applicata (LASA) lab, focuses on the development of steady-state magnet designs based on high-temperature superconductor (HTS) ReBCO (rare earth copper oxide) tapes. The paper presents a comparative analysis of energy consumption reduction in superferric dipole case studies for the Paul Scherrer Institut (PSI) accelerator complex, focusing on replacing conventional resistive coils with HTS windings optimized at 50 K in a window frame or h-type iron yoke. The outcomes of the proposed designs are compared against the existing resistive magnet performances, showing a strong advantage of this innovative approach for large-scale research facilities in terms of energy consumption and cost-effectiveness.
2 January 2024 in IEEE Transactions on Applied Superconductivity
The use of Canted Cosine Theta (CCT) magnets for accelerator applications has gained popularity due to their ease of manufacturing and assembly. In the context of two EU-Horizon2020-funded projects, HITRIplus and IFAST, the development of two 80 mm free bore and 4 T central field CCT dipoles for use in ion therapy (hadron therapy) is underway. In IFAST, a straight dipole CCT features a superimposed quadrupole component (combined function winding), while in HITRIplus a curved CCT (bending radius of 1.65 m) is wound as pure dipole. Both projects are based on a Cu/Nb-Ti multistrand rope as conductor. The article presents advancements in the engineering design of the magnets. A number of validation tests have been made to validate the choices made during the conceptual design. Characterization tests of the low losses rope, winding tests, splice tests, and impregnation tests will be described. The explored alternatives for the fabrication of the curved formers and the support structure are also discussed.