Minjie Shu

Minjie Shu

Auto-generated profile, based on publicly available information

Minjie Shu

China Academy of Space Technology (Xi’an), Xi’an, People’s Republic of China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 November 2020 in IEEE Access
Verified
Journal Article
Open access
FZFAN ZHANG
FAN ZHANG
Cheng GuoCheng Guo
Cheng Guo
YZYi Zhang
Yi Zhang
YGYang Gao
Yang Gao
BLBing Liu
Bing Liu
JXJun Xu
Jun Xu
This article presents a Ka-band fourth-order slotted spherical resonator waveguide bandpass filter (BPF) with a wide spurious suppression stopband. It uses the first higher-order TM211 mode rather than the fundamental TM101 mode of the spherical resonator in order to obtain a higher unload quality factor (Q u ) for smaller in-band insertion loss, as well as a larger filter volume that gives better tolerance to fabrication errors in high frequency applications. By introducing slots that interrupt surface currents, the fundamental TM101 and two higher spurious modes (TE101 and TM311) can be suppressed without compromising the unloaded quality factor of the TM211 mode. In addition, the filter topology is optimized to further enhance the suppression level of the spurious passbands. AZ-shaped topology has been found effective in decreasing the coupling strength of the spurious TM311 mode. An analysis is performed to demonstrate the better tolerance of the Z-shaped filter over the conventional TM101-mode spherical resonator filter. For verification, a fourth-order slotted spherical resonator waveguide BPF with a center frequency of 31 GHz and bandwidth of 880 MHz is designed and manufactured using a selective laser melting (SLM) 3-D printing process. The measured results show an average in-band insertion loss of 1.53 dB, and a passband return loss better than 13.6 dB. The stopband of the filter is extended up to 40.9 GHz with a rejection level greater than 20 dB.

13 July 2021 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
XWXiaozhu Wen
Xiaozhu Wen
Cheng GuoCheng Guo
Cheng Guo
XSXiaobang Shang
Xiaobang Shang
YYYang Yu
Yang Yu
MSMinjie Shu
Minjie Shu
AZAnxue Zhang
Anxue Zhang
This letter presents an eighth-order dual-mode waveguide filter, fabricated using the selective laser melting (SLM) technique. The filter employs four dimpled ellipsoid dual-mode resonators, operating at the fundamental TM 101 mode. During printing, the filter can be mechanically self-supported without any internal supports. Compared to the filters employing tuning posts, the proposed filter is less sensitive to fabrication errors in terms of their impacts on passband return loss (RL), frequency shift, and bandwidth. The filter was demonstrated at WR-112 band (7–10 GHz), with a measured insertion loss of 0.25–0.4 dB and an RL >15 dB across the passband of 8–8.46 GHz.

22 September 2020 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
MSMinjie Shu
Minjie Shu
Cheng GuoCheng Guo
Cheng Guo
XSXiaobang Shang
Xiaobang Shang
WZWeijun Zhu
Weijun Zhu
AZAnxue Zhang
Anxue Zhang
This letter presents the design of a new type of wideband waveguide matched loads. Unlike conventional loads based on absorbing materials, the proposed design relies on conductor loss of the waveguide to achieve the desired absorption level. To increase the waveguide loss and meanwhile maintain a small footprint of the whole device, gap waveguide structures are employed to reduce the group velocity of the wave inside the waveguide. Additionally, the waveguide is formed of walls with low conductivity metal, yielding much higher conductor loss. The waveguide load is designed to have a spiral shape for further reduction on size. The design is demonstrated at Ka-band (26.5-40 GHz) using 3-D printing technology. The measured S₁₁ of the prototype device is better than -20 dB across the entire Ka-band. This good result validates the proposed concept and reveals that the new lossy wall-based load can be a promising alternative to conventional designs particularly for applications involving high power or demanding superior stability over time.

13 November 2023 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
MSMinjie Shu
Minjie Shu
XSXiaobang Shang
Xiaobang Shang
NRNick Ridler
Nick Ridler
ACAntoine R. Calleau
Antoine R. Calleau
ADAlexandros I. Dimitriadis
Alexandros I. Dimitriadis
AZAnxue Zhang
Anxue Zhang
This article presents an in-depth study of material measurement, at G-band (140–220 GHz), using a commercially available material characterization kit (MCK). The permittivity of homogeneous dielectric materials, obtained from MCK measurements, rises slightly with frequency, and this does not agree with the expected physical behavior. Based on electromagnetic simulations and measurements, it has been identified that this small error is due to the dispersion associated with the corrugated horn antennas of the MCK. To address this problem, a simple phase compensation scheme has been proposed and applied to the measurement results of five common kinds of dielectric materials. The processed results eliminate the rising slope error observed in the raw data and are in good agreement with permittivity values reported in the literature, which validates the proposed approach.

30 April 2020 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
XLXiaobo Liu
Xiaobo Liu
MSMinjie Shu
Minjie Shu
Xiaoming ChenXiaoming Chen
Xiaoming Chen
AZAnxue Zhang
Anxue Zhang
In this article, we propose a 4-D characteristic matrix theory for the electromagnetic coupling of the multilayer metasurface system. The multilayer metasurface system is generally composed of periodic sub-wavelength metallic elements printed on the substrates. In the system, not only the coupling between multilayer metallic elements but also the coupling between different polarized waves can exist. In order to analyze the couplings and determine the total transmission (reflection) characteristic, a series of 4-D characteristic matrices are established for the substrates and metallic elements to relate the total tangential fields (two electrical components and two magnetic components) at adjacent interfaces. Finally, a four-layer metasurface system is designed to verify the theory whose results agree well with the simulated ones at arbitrary incidence angle. Unlike the existing methods, the four-dimensional characteristic matrix theory is not only independent of the anisotropy of the metallic elements, but also insensitive to the layer number of the metasurface. Thus, the proposed theory holds valid for arbitrary multilayer metasurface system, regardless of the layer number and the metallic elements.

4 December 2023 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
XLXiaobo Liu
Xiaobo Liu
MSMinjie Shu
Minjie Shu
AZAnxue Zhang
Anxue Zhang
Xiaoming ChenXiaoming Chen
Xiaoming Chen
In this paper, a dual-period impedance loaded transmission line model is established for the z-directed parallel plates with the x- and y-directed periodic interdigital-pin bed of nails. In the model, the y-directed periodicity is assumed to be smaller than the wavelength, and the height between two parallel plates is smaller than the half-wavelength. If so, for the periodic metallic nails in yoz plane, the zero-order Floquer’s mode as free wave exists in the structure and the high-order modes as surface waves are tightly bounded to the metallic nails. Thereby, the waveguide can be regarded as an x-direction transmission line alternately loaded by two types of periodic parallel impedances. Further, the dispersion equation is established to determine the pass band and forbidden band through the imaginary part of the propagation constant. Especially, if two kinds of parallel impedances are equal, the proposed theory can boil down to the existing dispersion model. Finally, based on the sinusoidal current distribution and the equivalent cross section assumptions, the calculus of variations is adopted to solve the analytical expression of the parallel impedance for the cylinder or rectangular nails. The simulations support the proposed theory, regardless of the periodic metallic rectangular and cylinder nails. Compared to the existing transverse resonance method, the proposed theory not only holds for interdigital (and non-interdigital) rectangular (and cylinder) nails, but also shows a higher accuracy for the non-interdigital cylinder nails, greatly enriching the dispersion theory.