Sergio Guillermo Torres Cedillo

Sergio Guillermo Torres Cedillo

Auto-generated profile, based on publicly available information

Sergio Guillermo Torres Cedillo

National Autonomous University of México

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2016 in Journal of Sound and Vibration
Verified
Journal Article
Closed access
SCSergio G. Torres Cedillo
Sergio G. Torres Cedillo
PBPhilip Bonello
Philip Bonello

24 April 2023 in Engineering Failure Analysis
Verified
Journal Article
Closed access
MJMoises Jimenez-Martinez
Moises Jimenez-Martinez
JVJulio Varela-Soriano
Julio Varela-Soriano
JCJosé Jorge Rojas Carreón
José Jorge Rojas Carreón
STSergio G. Torres-Cedillo
Sergio G. Torres-Cedillo

1 February 2019 in Mechanical Systems and Signal Processing
Verified
Journal Article
Closed access
SCSergio Guillermo Torres Cedillo
Sergio Guillermo Torres Cedillo
GAGhaith Ghanim Al-Ghazal
Ghaith Ghanim Al-Ghazal
PBPhilip Bonello
Philip Bonello
JPJacinto Cortés Pérez
Jacinto Cortés Pérez

7 April 2016 in Journal of Vibration and Control
Verified
Journal Article
Closed access
PDF file
SCSergio G Torres Cedillo
Sergio G Torres Cedillo
PBPhilip Bonello
Philip Bonello
The identification of nonlinear squeeze-film damper (SFD) bearings, typically used in aero-engines, has so far focused on their forward model (i.e. displacement input/force output). The contributions of this paper are the non-parametric identification of the inverse model of the SFD bearing (force input/displacement output) from empirical data, and its application to a nonlinear inverse rotor-bearing problem. This work is motivated by the need for a reliable substitute for internal instrumentation, to enable the identification of rotor unbalance using vibration data from externally mounted sensors, in applications where the rotor is inaccessible under operating conditions and there is no adequate linear connection between rotor and casing. The identification of the inverse model is fundamentally different from that of the forward model due to the need to account for system memory. A suitably trained Recurrent Neural network (RNN) is shown to be capable of identifying the inverse model of an actual SFD through two validation studies. In the first study, the RNN model satisfactorily predicted the SFD journal’s displacement time histories for given periodic time histories of the Cartesian SFD forces, although it could not predict the user-applied static offset in the SFD since it was not trained to do so. This was no limitation for the second study where, for both centred and non-centred SFD conditions, the RNN proved to be a reliable substitute for actual instrumentation as part of the inverse problem solution process for identifying the amplitudes and phases of the external excitation forces on a simple test rig.

25 July 2023 in Heliyon
Verified
Journal Article
Open access
MJMoises Jimenez-Martinez
Moises Jimenez-Martinez
JVJulio Varela-Soriano
Julio Varela-Soriano
JCJosé Jorge Rojas Carreón
José Jorge Rojas Carreón
STSergio G. Torres-Cedillo
Sergio G. Torres-Cedillo
Additive manufacturing is fast becoming a key process to manufacture a customized design with complex geometry and one process usually employed is based on the fused filament fabrication. Up to now this method is typically employed for rapid prototyping, it is therefore their mechanical strength is lower than the components manufactured using conventional casting process. It is well known that most failures are happened under repeated loads; therefore, a functional component mandatory needs to reach endurance strength under cyclic loads. Hence, this study set out to clarify several aspects of filament fused test specimens to determine their effect on accumulated damage to then predict component life under repeated loads. In this study is considered three waveforms such as sinusoidal, triangular and square, where it is observed that the square waveform provides the most severe loads. This study therefore makes a major contribution to research on the fatigue properties of parts manufactured using fused filament by reporting their fatigue behaviour under different fatigue load conditions. It would give a better understanding to improve the mechanical prediction of PLA, thereby it might be used to manufacture a functional component instead of only a prototype or spare part.

16 June 2014
Verified
Conference Paper
Closed access
PDF file
SCSergio G. Torres Cedillo
Sergio G. Torres Cedillo
PBPhilip Bonello
Philip Bonello
This paper is devoted to the unbalance identification and balancing of an aircraft engine rotor running on Squeeze Film Damper (SFD) bearings that show highly nonlinear features. The high pressure (HP) rotor in a twin-spool assembly cannot be accessed under operational conditions because of the restricted space for instrumentation and temperatures that are beyond the safe operating limits of the sensors. This motivates the use of a non-invasive procedure, requiring prior knowledge of the structure. The only such method for rotating machinery with non-linear bearings reported in the literature is highly limited in its application (e.g. assumes circular centred orbits). The methodology proposed in this paper is aimed at overcoming such limitations. It uses the Receptance Harmonic Balance Method (RHBM) to generate the backward operator using vibration measurements taken from sensors installed on the engine casing. The operator is then inverted using either Least Squares Fit (LSF) or Singular Value Decomposition (SVD). The resulting solution is the equivalent unbalance distribution in prescribed unbalance planes of the HP rotor which are consequently used to balance it. This method is validated using two distinct rotordynamic systems and simulated casing vibration readings corrupted by different noise levels.