10 February 2022 in IEEE Transactions on Instrumentation and Measurement
A very small focal-to-diameter (F/D) ratio transmitarray for compact antenna test range (CATR) application is proposed in this article. The transmitarray comprises a feed antenna, a metasurface for phase modulation (MPM), and another one for amplitude modification (MAM). MPM and MAM are implemented using the same metasurface cell but with different cell selections and arrangements. A holistic phase-only design method determines whether the metasurface is for amplitude modification or phase modulation. A CATR collimator with an overall low profile is realized through the joint design of MAM and MPM. The proposed technique overcomes the limits of the ordinary metasurface lenses and enables plane wave generation with a short focal length and sizeable quiet zone. The resulting CATR demonstrates a 50% quiet zone of the aperture size with ±0.5-dB amplitude and ±5° phase errors by full-wave simulation. For further verification, a prototype is fabricated, and its experimental results confirm the simulations.
28 March 2022 in IEEE Transactions on Antennas and Propagation
Millimeter-wave (mm-Wave) band channel modeling and characterization are essential for system design and analysis in the fifth generation (5G) and future communication systems. Reliable channel sounding in the deployment scenarios is required for accurate and realistic channel modeling and characterization. In the state of the art, directional scanning sounding (DSS) and virtual antenna array (VAA) sounding are two popular methods due to their simplicity and cost-effectiveness. The DSS and the VAA methods are typically based on mechanically rotatable directional antennas and mechanically movable omnidirectional antennas, respectively. However, the spatial resolution is limited by the directivity and high sidelobes of the directional antennas used in the DSS method. The conventional VAA method also has limitations in terms of the low signal-to-noise ratio (SNR) and the unavailability of suitable omnidirectional antennas that support mmWave (above 60 GHz) band measurements and wideband horizontal polarization measurements. In this article, a novel directional antenna-based VAA framework in combination with the associated beamforming algorithm is proposed. Compared to the state-of-the-art methods, the proposed framework can achieve high angular resolution and high SNR for mm-Wave channel measurements without introducing additional cost and measurement time. Furthermore, it is a generic solution that can be applicable for arbitrary frequency bands and polarizations, unlike the conventional VAA method. To validate the effectiveness and robustness of the proposed method, experiments in two scenarios (a clean anechoic chamber and a realistic indoor meeting room) were conducted over 28–30 GHz with two types of directional antennas (i.e., a horn antenna and a corrugated antenna). Besides, the advantages of the proposed method are highlighted with a comparison to the conventional VAA and DSS methods.
27 October 2023 in IEEE Communications Magazine
The sixth-generation (6G) communication system will leverage the evolving multiple-input-multiple-output (MIMO) technology, referred to as gigantic MIMO. It is envisioned to accommodate arrays with over one thousand antennas for low and mid frequency bands, and with up to thousands of antennas for high frequency bands such as THz. With such a substantial number of antenna elements, the gigantic MIMO technology has the potential to unlock new use cases and applications with extreme requirements. Radio channel characterization plays a crucial role in the design, optimization, and performance evaluation of these radio systems, making it highly desirable for advancing the deployment of the gigantic MIMO technology. This article discusses key challenges and potential solutions for radio channel characterization of gigantic MIMO systems, including channel modeling approaches, experimental platform development i.e., channel sounder design, and radio channel parameter estimation. Further, a channel measurement campaign based on a virtual antenna array (containing 2400 antenna elements) and a corresponding ray tracing simulation are performed for a practical indoor scenario as examples to characterize a realistic gigantic MIMO channel.
2 July 2021 in IEEE Transactions on Vehicular Technology
This paper presents a novel method of improving the correlation performance in a compact multiple-input multiple-output (MIMO) array. Unlike the previous work, the proposed method focuses on each antenna phase distribution in the array and reduces the correlation by adjusting the near-field phase distribution using phase correcting elements (PCEs). The PCEs provide the required transmission phase to modify the near-field phase distribution in a specific plane. Diversity measure and channel capacity are introduced as metrics to evaluate the MIMO system's array performances. The significance of the phase pattern on the correlation performance is investigated and demonstrated by comparing and analyzing four specially designed arrays' results. A 1 × 4 dual-polarized patch array with four PCEs is simulated, fabricated, and measured to verify the method. The diversity measure and channel capacity are improved by 0.5 (10%), 5 bit/s/Hz (12.2%), respectively, at 2.6 GHz when the channel's angular spread is 90°.
15 August 2023 in IEEE Transactions on Antennas and Propagation
Over-the-air (OTA) radiated testing is seen inevitable for future radio devices due to integrated transceiver radio designs. Wireless cable solution, which can achieve traditional cabled testing functionality over-the-air, has attracted great attention from industry, standardization and academia in recent years for multiple-input multiple-output (MIMO) device performance testing. In state-of-the-art wireless cable solutions, the compensation of the transfer matrix between the OTA probes and antenna ports of device under test (DUT) is implemented with the help of radio channel emulators (CEs). However, the radio CEs are not customized for such implementations, leading to expensive system and waste of valuable CE resource. Employing more probe antennas is a known and effective strategy to improve the robustness and quality of the wireless cable connection, which would further increase the system cost with existing implementations. To address these issues, a novel wireless cable implementation employing a stand-alone programmable amplitude and phase control network is proposed. Though simple and cost-effective, the proposed scheme is demonstrated to work in practice and it is applicable for more generic testing scenarios where a CE is not required. The experimental validation measurements obtained in the VNA based passive measurement setup as well as in the active measurement setup clearly demonstrate the effectiveness and robustness of the proposed scheme.
11 May 2023 in IEEE Transactions on Instrumentation and Measurement
To ensure millimeter-wave (mmWave) radio system performance, multiple beam-steered radiation patterns of phased arrays are required to be measured in conventional antenna measurement ranges. This is typically done by sequentially measuring the radiation pattern of phased array under test (AUT) with the AUT mechanically rotating in a far-field setup for each steered beam in a beam-lock mode. However, the conventional pattern measurement procedure for mmWave phased arrays with multiple beams is time-consuming and costly due to the repetitive mechanical rotation and the use of far-field anechoic chamber. The problem becomes even more pronounced for mmWave phased arrays with large-scale antenna configuration due to many more beam states and more directive beam patterns. To address this issue, this paper proposes a novel near-field multi-beam measurement system for mmWave phased arrays, which offers unique advantages in terms of short measurement time, support for full automation, no need for mechanical rotation, compact measurement setup and low system cost. For the pattern with its beam steered to any given direction can be reconstructed based on the AUT element patterns retrieved from a few sparse measurement samples. In this work, the principle and effectiveness of the proposed measurement system have been firstly validated by electromagnetic simulations with CST Studio Suite. Besides, a practical system prototype has been built and experimentally validated where the near-field reconstructed multi-beam patterns are shown to match well with the far-field target patterns in terms of beam direction, beam gain, and pattern similarity percentage.