The effects of low amounts (0, 0.1, 0.3, 0.5, 0.8, 1, 2vol%) of Sm2O3 on the densification, microstructure, and bending strength of Al2O3 were studied for different sintering temperatures. Sm2O3 and Al2O3 powders were mixed by ball milling, and Al2O3-Sm2O3 ceramics were prepared by dry and cold isostatic pressing in disc form before pressureless sintering at 1550°C and 1600°C/2 h in the air, separately. Sm2O3 reacted with Al2O3 by forming SmAlO3. The rod-like morphology of the SmAlO3 was generally achieved for 0.8 and 1vol% Sm2O3 for sintering at 1600°C, whereas the rod-like form was more obvious for the samples sintered at 1550°C. Similar relative densities were attained for all Sm2O3 ratios at both sintering temperatures, but the Al2O3 sintered at 1550°C exhibited higher densification than the Al2O3 sintered at 1600°C. The strength values were close, while a strength increase of about 5% was obtained for 0.5 vol% Sm2O3 containing ceramics sintered at 1600°C caused by the higher densification compared to the Al2O3. The strength showed a prominent drop above the ratio of 0.1 vol% Sm2O3 for sintering at 1550°C. The addition of present amounts of Sm2O3 did not have a significant effect on the mechanical properties of Al2O3 but it changed the microstructure.
This work aimed to compare the mechanical properties and microstructures of Al2024-graphene, Al6061-graphene, and Al7075-graphene composites produced via the induction hot pressing and powder metallurgy method. The influences of graphene content (0.15-0.45wt.%), heat treatment (sintering and induction hot-pressing), and matrix material (Al2024, Al6061, and Al7075) on the mechanical strength and microstructure of specimens were studied. Compared to Al2024, Al6061 and Al7075 alloys, the compressive strength of Al2024-0.15graphene, Al6061-0.15graphene and Al7075-0.15graphene composites increased by 33.74%, 24.9% and 32%, respectively. The highest compressive strength (506±5 MPa), hardness (164±1.5 HV), and apparent density (2.65 g/cm3) were achieved in sintered and induction heat-treated Al7075-0.15%graphene composite. As a result, it was determined that graphene is an effective reinforcement element. It has been determined that induction hot-pressing improves the mechanical strength of composite materials.
16 June 2025 in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Bu çalışmada, Al7075 matrisli B4C takviyeli kompozitler toz metalürjisi ve sıcak presleme yöntemleri ile üretilmiştir. Al7075 matrise ağırlıkça %1, 3, 6, 9, 12, 15 ve 30 oranlarında B4C ilave edilmiştir. Üretilen kompozitlerin deneysel yoğunluğu, Vickers sertliği, aşınma oranı ve sürtünme katsayısı belirlenmiştir. Elde edilen sonuçlara göre en yüksek deneysel yoğunluk (2,63 g/cm3), Vickers sertliği (226 HV) ile en düşük aşınma oranı ((0,000091 mm3/(Nm)), kütle kaybı (0,0012 g) ve sürtünme katsayısı (0,4) Al7075-30B4C kompozitte elde edilmiştir. Ayrıca yapılan mikroyapı analizleri ile bu kompozitte mikroyapının daha yoğun olduğu gözlemlenmiştir. Çalışma sonucunda Al7075 alaşımına belirli katkı oranında (ağırlıkça %30) B4C ilave edildiğinde kompozitin mikroyapısının ve tribolojik özelliklerinin iyileştiği tespit edilmiştir.
15 September 2024 in Black Sea Journal of Engineering and Science
In this study, ZrO2 honeycomb sandwich structures with different cellular geometry were manufactured by SLA 3D-printing technology to analyze the compressive strength behaviour. After the printing procedure, the samples were sintered at 1450 °C for 2h. Among the samples with different cellular geometry, ZrO2 parts with circular cells were superior to that of square and triangular honeycomb structures and 1867±320 MPa compressive strength was obtained for this structure. The stress distributions in honeycomb structures were investigated using the COMSOL Multiphysics® for exposing the effect of cellular geometry on compressive strength. While more uniform stress distributions were seen on the inner wall of the circular honeycomb sample, the cellular structure of the square and triangle honeycomb samples mostly displayed compressive stress concentration on the joints of the honeycomb structure. Also, according to Rankine failure criterion, the parts with square cellular geometries were found to be more prone to failure. The highest specific compressive strength was obtained for the ZrO2 parts with circular cellular geometry. These findings demonstrated that the ZrO2 honeycomb sandwich structures with circular cellular geometry produced using SLA ceramic 3D-printing technology may be a suitable material to utilize in lightweight structural designs.
15 April 2025 in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
Yapılan bu çalışmada toz metalürjisi ve sıcak presleme yöntemleriyle Al7075 matrise ağırlıkça %1, 3, 6, 9 ve 12 katkı oranlarında Si3N4 ilave edilerek kompozit malzemeler üretilmiştir. Üretilen kompozitlere yoğunluk, Vickers sertliği, aşınma ve sürtünme testleri uygulanmıştır. Ayrıca kompozitlerin mikroyapılarını incelemek amacıyla XRD, SEM ve SEM-EDX analizleri yapılmıştır. Sonuç olarak en yüksek deneysel yoğunluk (2.65 g/cm3), en yüksek Vickers sertliği (205 HV), en düşük aşınma oranı (0.00018 mm3/(Nm)), en düşük kütle kaybı (0.0025 g) ve en düşük sürtünme katsayısı (0.38) değerleri Al7075-%9 Si3N4 kompozitte elde edilmiştir. Ancak ağırlıkça %12 Si3N4 katkı oranında takviye partiküllerinin topaklanmasından dolayı kompozitin tribolojik özellikleri kötüleşmiştir. Sonuç olarak Al7075 matrise %9 Si3N4 katkısının kompozitin tribolojik özelliklerini iyileştirdiği tespit edilmiştir.
Yapılan bu çalışmada toz metalürjisi ve sıcak presleme yöntemleriyle Al7075 matrise farklı oranlarda (ağırlıkça %1, 3, 6, 9 ve 12) Si3N4 takviye edilmiştir. Katkı oranının üretilen kompozitlerin mikroyapılarına ve mekanik özelliklerine (yoğunluk, gözeneklilik oranı, Vickers sertliği ve basma dayanımı) olan etkisi incelenmiştir. Yapılan testler sonucunda en yüksek yoğunluk (2,65 g/cm3), Vickers sertliği (205 HV), basma dayanımı (344 MPa) ve en düşük gözeneklilik oranı (%7,5) Al7075-9Si3N4 kompozitte elde edilmiştir. Mikroyapı incelemeleri sonucunda ise %9Si3N4 katkı oranında takviye partiküllerinin matris içerisinde homojene yakın bir şekilde dağıldığı belirlenmiştir. Sonuç olarak Al7075 matrise %9Si3N4 katkısının kompozitin mikroyapısını yoğunlaştırdığı ve mekanik özelliklerini iyileştirdiği tespit edilmiştir.