Mengtao Liang

Mengtao Liang

Auto-generated profile, based on publicly available information

Mengtao Liang

Xi’an Jiaotong University

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 October 2023 in Advanced Engineering Materials
Verified
Journal Article
Closed access
MLMengtao Liang
Mengtao Liang
HWHuagen Wu
Huagen Wu
SCSiwei Chen
Siwei Chen
ZFZeming Fu
Zeming Fu
RZRongshan Zhang
Rongshan Zhang
ZXZiwen Xing
Ziwen Xing

5 August 2025 in Thin-Walled Structures
Verified
Journal Article
Closed access
MLMengtao Liang
Mengtao Liang
HWHuagen Wu
Huagen Wu
Tao YangTao Yang
Tao Yang
WLWenjian Liu
Wenjian Liu
MIMartin Ibarias
Martin Ibarias
JSJosé Sánchez-Dehesa
José Sánchez-Dehesa

17 June 2025 in Thin-Walled Structures
Verified
Journal Article
Open access
MLMengtao Liang
Mengtao Liang
HWHuagen Wu
Huagen Wu
MIMartin Ibarias
Martin Ibarias
Jose Sanchez-DehesaJose Sanchez-Dehesa
Jose Sanchez-Dehesa

9 March 2024 in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Verified
Journal Article
Closed access
HWHuagen Wu
Huagen Wu
MLMengtao Liang
Mengtao Liang
SCSiwei Chen
Siwei Chen
GWGuanghua Wu
Guanghua Wu
HHHongye Huang
Hongye Huang
ZXZiwen Xing
Ziwen Xing
The oil-free twin screw compressors have obtained increasing attention in the field of boil off gas (BOG) recovery since they effectively reduce the power consumption and have higher reliability when recovering and boosting BOG. However, the thermal deformation of compressor under cryogenic operating conditions will lead to the change of clearance. The unidirectional thermal-fluid-solid coupling method is proposed in this paper to solve the problem and analyze the thermal deformation of compressor and the changes of each clearance caused by the deformation at different meshing angles in a meshing cycle. It is shown in the results that the deformation of twin screw compressor at low temperatures is a kind of cold shrinkage deformation. The combined effect of the deformation of various components has a significant influence on each clearance. Furthermore, it is reasonable to set the tooth tip clearance of the male rotor, suction end clearance and meshing gap as 0.3 mm, 1 mm and 0.3 mm respectively, which do not cause dangerous working conditions. Inappropriate clearance values lead to friction between parts in the local area. The simulated result of the dangerous friction area in twin screw compressor shows good agreement with the friction area in the compressor test. According to the simulation and test results, the tooth tip clearance of the female rotor is modified to 0.35 mm, and the discharge end clearance is adjusted to 0.1 mm. The results show that the modified compressor can working reliably. This study provides guidance for the design and processing of oil-free twin screw compressors employed in the situation of BOG recovery.

1 May 2020
Verified
Conference Paper
Closed access
ZHZhuangzhi Han
Zhuangzhi Han
YWYuzhu Wu
Yuzhu Wu
MLMengtao Liang
Mengtao Liang
YMYuehong Ma
Yuehong Ma
XLXiaomin Li
Xiaomin Li
The leakage of transmitter signal seriously restricts the improvement of CW radar detection performance. Microstrip antenna is widely used in miniature CW radars, and its isolation performance is the key to restrict the detection ability of miniature CW radars. In this paper, the techniques of suppressing transmitter signal leakage in CW radar system are analyzed, including transceiver channel cancellation, signal processing, and antenna isolation technology, It is pointed out that the transmission and reception isolation of microstrip antennas is mainly realized by spatial isolation technology, including two types of spatial wave isolation and surface wave isolation. The principles, characteristics and applications of spatial wave isolation technology and surface wave isolation technology are analyzed in detail. Finally, it is pointed out that the main goal of increasing the transceiver isolation is to improve the sensitivity. It is difficult for a single technology to meet the requirements of isolation, and it is necessary to implement multiple methods based on the specific application.

1 April 2026 in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Verified
Journal Article
Closed access
GCGuoao Chen
Guoao Chen
HWHuagen Wu
Huagen Wu
DFDelin Feng
Delin Feng
YZYishan Zhou
Yishan Zhou
YWYang Wang
Yang Wang
ZXZiwen Xing
Ziwen Xing
Oil-injected screw compressors use oil-injected lubrication and sealing. Compared with dry screw compressors, they reduce costs and improve performance and have been widely applied in the refrigeration and industrial gas fields. Firstly, a comprehensive mathematical model of the oil-injected twin-screw compressor was constructed, and an experimental platform for performance testing of the oil-injected twin-screw air compressor was established. The mathematical model was verified, and the accuracy of the simulation results was verified. Subsequently, the response surface models of oil injection volume, oil injection temperature, oil injection port position and back pressure were established by using the Box-Behnken method, and the interactions of oil injection volume, oil injection temperature, oil injection port position and back pressure with volumetric efficiency, adiabatic efficiency and specific power were analyzed. The results show that optimizing volumetric efficiency and adiabatic efficiency merely by adjusting the oil injection volume is contradictory. When optimizing performance, the oil injection temperature should be reduced as much as possible. Finally, the oil injection parameters of the oil-injected screw compressor were optimized by using the non-dominated sorting multi-objective genetic algorithm (NSGA-II), and the optimal oil injection parameters under different rotational speeds were obtained using the entropy-weighted TOPSIS (E-TOPSIS) method. The average volumetric efficiency of the optimized compressor has increased by 2.76%, the average adiabatic efficiency has increased by 3.39%, and the average specific power has decreased by 3.28%. This method effectively improves the performance of the twin-screw compressor.