28 October 2023 in Minerals Engineering
26 April 2023 in Minerals Engineering
29 July 2021 in Minerals Engineering
19 June 2019 in Particulate Science and Technology
This paper aimed to investigate the applicability of impact bed breakage test for model fitting of continuous dry horizontal stirred mill. Initially, the breakage tests were performed for three types of materials at varying bed diameters, 2 cm, 3 cm, 4 cm, and 6 cm to find out the optimal bed geometry. The test results for the three materials showed that the bed height of 4 cm was optimal as the fines’ generation reached to a plateau and decided to be used in model fitting of the dry stirred mill. Afterward, cement material was processed within the dry stirred mill and samples were collected from feed and product ends when the steady-state conditions were established. The results of the grinding tests on cement material together with its breakage results obtained from 2 cm and 4 cm diameter beds were used in the model fitting of the mill by using perfect mixing approach. Accurate model fitting was obtained in case 4 cm diameter of bed was utilized and the predictions were in good agreement with the measured size distributions even if the operating conditions of the mill were changed.
1 December 2019 in Bilimsel Madencilik Dergisi
Tr en Öğütme devrelerinin modellenmesi, devre tasarımı ve optimizasyonu açısından önem taşımaktadır. Doğru ve güvenilir modeller için malzemenin kırılma dağılımı fonksiyonunun tayin edilmesi önem arz etmektedir. Çalışmada, her bir kamara için ayrı kırılma testlerinin kullanıldığı model yapısı üzerine odaklanılmıştır. Çalışma kapsamında, 2 kamaralı bilyalı değirmen içeren çimento öğütme devresi etrafında ve değirmen içinde örnekleme çalışmaları yürütülmüş ve alınan numunelerin tane boyu dağılımları belirlenmiştir. Sonrasında madde denkliği çalışmaları yürütülmüştür. Değirmenin ilk kamarası için tek tane ağırlık düşürme testleri, ikinci kamarası için ise Hardgrove kırma testleri yürütülmüş ve tane boyuna bağlı kırılma dağılım fonksiyonları hesaplanmıştır. Çalışma Hardgrove tekniğinin bilyalı değirmen modelindeki ilk uygulamasıdır. Kamaralar ayrı olarak mükemmel karışım modeli kullanılarak modellenmiştir. Simülasyon sonuçları ürün tahminlerinin 1. kamarada tutarlı olduğu ve 2. kamarada ise Hardgrove testinin tek tane testine göre daha olumlu sonuçlar verdiğini göstermiştir. Modelling of grinding circuits is crucial for circuit design and optimization. Determination of breakage distribution function of the materials is important for accurate and reliable modelling. In this study, the model structure was focused on using separate breakage tests for each chamber. Within the study, sampling studies were performed around the grinding circuit containing 2-chamber ball mill and inside the mill and, particle size distributions of collected samples were determined. Then mass balance studies were performed. Single particle drop weight test for the chamber-1 while Hardgrove test for the second chamber of the mill was carried out then size-dependent breakage distribution functions were calculated. The study is the first application of using Hardgrove technique in the ball mill model. Each chamber was modelled separately by using Perfect Mixing Model. Simulation results showed that the product estimations were accurate for the chamber-1 that the Hardgrove test was suitable for the chamber-2.
16 July 2019 in Mineral Processing and Extractive Metallurgy: Transactions of the Institutions of Mining and Metallurgy
Pilot scale grinding tests were performed for various materials by a mobile unit for modelling studies. Vertical roller mill was separated into the two section as grinding and separation. Grinding operation was defined by population balance model and breakage rate was correlated with specific grinding force, material index determined by compressed bed breakage tests and surface area of grinding table feed. For the modelling of separation section, obtained data were fitted to efficiency curve approach and model parameters were back calculated. Relationships of these parameters with operational conditions were investigated. As a first model parameter by pass fraction of was correlated with dust load of the separator feed. Then, by pass fraction was defined as a function of the dust load of the separator feed and material density. The ratio of air speed and rotor speed was correlated with corrected cut size and density effect was reflected to the model.