Ahmet Hakan Benzer

Ahmet Hakan Benzer

Auto-generated profile, based on publicly available information

Ahmet Hakan Benzer

Hacettepe Üniversitesi

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2019 in Bilimsel Madencilik Dergisi
Verified
Journal Article
Closed access
PDF file
ÖGÖmürden Genç
Ömürden Genç
ABAhmet Hakan Benzer
Ahmet Hakan Benzer
In this study, open circuit single and two stage industrial scale vibrating ball mill (VBM) grinding performance of raw (uncrushed) cement clinker was investigated using different mill feed size distributions and grinding ball size configurations. The mill was modelled for the test cases using perfect mixing mathematical modelling approach. Different ball size configurations were applied in the grinding tests to estimate the effect of ball size configuration on grinding performance. Proposed coarse ball size configuration (30-20-15mm) was determined to increase the size reduction performance of single stage VBM grinding when coarse mill feed material was fed to the VBM (F50=185μm) as compared to the finer mill feed case (F50=24μm). VBM grinding performance was determined to increase with finer mill feed material (F50=24μm) and application of finer ball size configuration (10-8-6mm) in single stage grinding case as compared to the two stage grinding case.

16 July 2019 in Mineral Processing and Extractive Metallurgy: Transactions of the Institutions of Mining and Metallurgy
Verified
Journal Article
Closed access
DADeniz Altun
Deniz Altun
HBHakan Benzer
Hakan Benzer
Pilot scale grinding tests were performed for various materials by a mobile unit for modelling studies. Vertical roller mill was separated into the two section as grinding and separation. Grinding operation was defined by population balance model and breakage rate was correlated with specific grinding force, material index determined by compressed bed breakage tests and surface area of grinding table feed. For the modelling of separation section, obtained data were fitted to efficiency curve approach and model parameters were back calculated. Relationships of these parameters with operational conditions were investigated. As a first model parameter by pass fraction of was correlated with dust load of the separator feed. Then, by pass fraction was defined as a function of the dust load of the separator feed and material density. The ratio of air speed and rotor speed was correlated with corrected cut size and density effect was reflected to the model.

2 December 2025 in Minerals Engineering
Verified
Journal Article
Closed access
SCSerkan CAYIRLI
Serkan CAYIRLI
HGHasan Serkan Gokcen
Hasan Serkan Gokcen
NYNuri Yuce
Nuri Yuce
OEObaidullah Elchi
Obaidullah Elchi
ABAhmet Hakan Benzer
Ahmet Hakan Benzer

1 June 2018 in Bilimsel Madencilik Dergisi
Verified
Journal Article
Closed access
PDF file
ÖGÖmürden Genç
Ömürden Genç
ABA.Hakan Benzer
A.Hakan Benzer
The purpose of the study is to assess the grinding and classification performance of aconventional Polysius® two-compartment ball mill and a Sepol® dynamic air classifier closedcircuit process at Portland CEMI/42.5R and Portland composite CEMII/32.5R cement productiontypes. For this purpose, industrial scale sampling surveys were performed around the circuit.JKSimMet Steady State Mineral Processing Software was used to perform mass balance aroundthe circuits. Size reduction performance of the ball mill was determined for the sampling cases.Classification performance of the dynamic air classifier was evaluated based on the efficiencycurve approach. It was determined that, approximately 12% circuit capacity increase could beachieved in composite cement production when ball mill, ball mill filter and air classifier powerconsumptions were considered. This figure corresponded to overall energy savings of 7% in ballmill grinding.