Xiaobin Zhu

Xiaobin Zhu

Auto-generated profile, based on publicly available information

Xiaobin Zhu

Ph.D. Candidate, Science and Technology on Scramjet Laboratory, National Univ. of Defense Technology, Changsha, Hunan 410073, China

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2017 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
ZCZun Cai
Zun Cai
XZXiaobin Zhu
Xiaobin Zhu
MSMingbo Sun
Mingbo Sun
ZWZhenguo Wang
Zhenguo Wang

1 June 2019 in Acta Astronautica
Verified
Journal Article
Closed access
XZXiaobin Zhu
Xiaobin Zhu
ZCZun Cai
Zun Cai
JWJianjun Wu
Jianjun Wu
YCYuqiang Cheng
Yuqiang Cheng
QHQiang Huang
Qiang Huang


1 July 2021 in Aerospace Science and Technology
Verified
Journal Article
Closed access
RHRunsheng Hu
Runsheng Hu
RFRiccardo M.G. Ferrari
Riccardo M.G. Ferrari
ZCZhenyu Chen
Zhenyu Chen
YCYuqiang Cheng
Yuqiang Cheng
XZXiaobin Zhu
Xiaobin Zhu
JWJianjun Wu
Jianjun Wu

1 September 2018 in Journal of Aerospace Engineering
Verified
Journal Article
Closed access
ZCZun Cai
Zun Cai
XZXiaobin Zhu
Xiaobin Zhu
MSMingbo Sun
Mingbo Sun
ZWZhenguo Wang
Zhenguo Wang
In this study, experiments were conducted in a Mach 2.92 supersonic flow to investigate the combustion process in an ethylene-fueled model scramjet combustor with a rear-wall-expansion geometry. It is concluded that at low equivalence ratios, successful ignitions would become rather hard in the cavity with a low rear wall height. Increasing the equivalence ratio could improve the ignition environment within such cavity geometry. During a stable combustion process, the rear-wall-expansion cavity with a higher rear wall height would always achieve an improvement in combustion performance in the combustor. At a relatively high equivalence ratio, when increasing the cavity rear wall height, the flame stabilization mode would vary from cavity shear layer-stabilized mode to cavity-assisted jet wake–stabilized mode, and finally to the thermal choking state. Besides, reaction zones flashback phenomenon is obviously observed during the flame propagation process at such equivalence ratio. It has been demonstrated that the cavity with a lower rear wall height is more able to prevent thermal choking in the combustor.

16 June 2014
Verified
Conference Paper
Closed access
PDF file
CWCun Wang
Cun Wang
DZDayi Zhang
Dayi Zhang
XZXiaobin Zhu
Xiaobin Zhu
JHJie Hong
Jie Hong
The bolted flange joint is a kind of widely used joint structure in the rotor system. Its discontinuous mechanical characteristics result from the existing of the contact surface, which will slide and deform when the spool deforms. As a consequence, the joint’s stiffness is always smaller than that of fixed configuration, which affects rotor’s stiffness distribution and the rotor’s dynamics further. The objective of this study is to investigate the mechanical characteristics of the bolted flange joint, the affecting factors and the influence on rotor’s dynamics. According to the characteristics of structure and mechanical state, using the existing equivalent axial spring-bending beam model to describe the tension and compression stiffness of bolted flange joint section, then the bending stiffness model of whole bolted flange joint is established based on that. The results show that there is a significant effect of the bolted flange joint on the local stiffness of the rotor, the loss of local bending stiffness reach a high level when the number of bolts is few. The mathematical description between stiffness loss and structure size, load and assembling condition is obtained through the analytical results. A bolted flange joint simulation model, taking the characteristics of the contact into account, is built by the nonlinear finite element method. The trends of numerical results agree with the analytical conclusion, and show the stiffness of bolted flange joint is smaller than that of the fixed configuration. The stiffness of bolted flange joint decreases a small amount with the increasing moment. When the number and the pretension force increases, the stiffness increases nonlinearly. Based on the mechanism of stiffness loss, the equivalent stiffness is used to replace the fixed configuration stiffness on the location of bolts in finite element model of high pressure rotor system. The results of dynamic analysis shows that the stiffness loss has a greater impact on bending modes than the rigid modes while the static analysis shows that the stiffness loss has a small negatively effect on clearances. The study shows that, the stiffness loss of bolted flange joint has a close relationship with the load and assembling conditions. The results show the effectiveness in controlling the mechanical and dynamic properties of the rotor with bolted flange joints by careful adjusting of structural parameter, load parameter and assembling parameter during designing.