To develop the satellites for a low-Earth-orbit environment, atmosphere-breathing electric propulsion (ABEP) systems have become more attractive to researchers in the past decade. The system can use atmospheric molecules as the propellant to provide thrust compensation, which can extend the lifetime of spacecraft (S/C). This comprehensive review reviews the efforts of previous researchers to develop concepts for ABEP systems. Different kinds of space propulsion system are analysed to determine the suitable propulsion for atmosphere-breathing S/C. Further discussion about ABEP systems shows the characteristic of different thrusters. The main performance of the ABEP system of previous studies is summarized, which provides further research avenues in the future. Results show great potential for thrust compensation from atmospheric molecules. However, the current studies show various limitations and are difficult to apply to space. The development of ABEP needs to solve some problems, such as the intake efficiency, ionization power, and electrode corrosion.
In this paper, a non-Fourier heat conduction model of ultra-short pulsed laser ablation of metal is established that takes into account the effect of the heat source, laser heating of the target, the evaporation and phase explosion of target material, the formation and expansion of the plasma plume, and interaction of the plasma plume with the incoming laser. Temperature dependent optical and thermophysical properties are also considered in the model due to the properties of the target will change over a wide range during the ultra-short pulsed laser ablation process. The results show that the plasma shielding has a great influence on the process of ultra-short pulsed laser ablation, especially at higher laser fluence. The non-Fourier effect has a great influence on the temperature characteristics and ablation depth of the target. The ultra-short pulsed laser ablation can effectively reduce the heat affected zone compared to nanosecond pulsed laser ablation. The comparison between the simulation results and the experimental results in the literature shows that the model with the plasma shielding and the non-Fourier effect can simulate the ultra-short pulsed laser ablation process better.
The increasing demand for high energy density fuels and the concern for their safety have propelled research in the field of gelled propellants, where understanding the combustion of single gelled fuel droplets is the first stage to predict the spray combustion characteristics. The experiments utilized single-isolated freely falling gelled unsymmetrical dimethylhydrazine (UDMH) droplets instead of the conventional suspended droplet approach, in order to eliminate the perturbation associated with the suspension mechanism. Morphological transformations of the gelled droplet involved in the combustion processes were monitored by employing a high-speed digital camera, while the effects of ambient pressure and oxygen concentration on burning rate constants were also studied. The experimental results show that four main phenomena (droplet deformation, bubble formation and growth, vapor jetting and luminous jetting flame with “horn” shape) and three distinct phases were identified in the droplet combustion process; the high yield stress and polymer chain structure of polymer gellant are responsible for the appearance of bubbles with almost the same order of magnitude as the droplets. Increasing the ambient pressure can increase the burning rate, postpone the appearance of microexplosions, and weaken microexplosion intensity; while increasing the ambient oxygen concentration can promote the appearance of microexplosions, strengthen microexplosion intensity and increase the burning rate.
To study the plasma plume expansion dynamics of nanosecond laser ablating Al/PTFE, the Al/PTFE propellant was prepared by a molding sintering method and the rapid expansion process of the plasma plume was photographed using fast photography technology. The effects of the proportion of Al, laser energy and ambient pressure on plasma plume expansion dynamics are analyzed. The results show that the plume expansion process of laser ablating Al/PTFE plasma can be divided into three stages and this phenomenon has not been reported in the literature. The Al powder doped in PTFE will block part of the laser transmission into the propellant, thus reducing the laser absorption depth of the propellant. In the case of short pulse laser ablation, the reaction rate between Al and PTFE is optimal when the reductant is slightly higher than the oxidant. As the laser energy increases, the light intensity of the plasma becomes stronger, the plasma size becomes larger and the existence time of plasma becomes longer. In the first stage plume, the plume expands freely at the ambient pressure of 0.005 Pa and the plume expansion distance is linearly related to time, while the shock wave formed at the interface between the plume front and the ambient gas at the ambient pressure of 5 Pa and the expansion can be described by S-T theory.
This paper introduces a new direct non-contact electromagnetic calibration technique for high precision measurements of micro-thrust and impulse. A ring-shaped electromagnet with an air gap is used in the calibration. The calibration force is produced by the interaction of a uniform magnetic field with a copper wire current in the air gap. This force depends linearly on this current as well as the steady angular displacement of the torsion arm of the thrust stand. The range of calibration force is very large and the calibration force is easy to generate and insensitive to the arm displacement. The calibration uncertainty for a 150-μN force is 4.17 μN. The more influential factor on the calibration uncertainty is the magnetization of the electromagnet core due to the copper wire current. In the impulse calibration, the exerted impulse is linearly dependent on the maximal angular displacement of the torsion arm. The uncertainty in the impulse calibration is determined by uncertainties in both the force calibration and the pulse time.