The effects of temperature on performance of a grid-connected inverter, and also on a photovoltaic (PV) system installed in Thailand have been investigated. It was found that the maximum efficiency of the inverter showed 2.5% drop when ambient temperature was above 37°C. The inverter performed efficiently in November and December, the months of high irradiance, and monthly average ambient temperature of lower than 35°C, allowing relatively high system performance ratio in this period. Our results show that high temperature provides negative impacts not only on the PV modules, but also on the performance of the inverter. Thus, the effect of temperature on the inverter efficiency should be taken into account when predicting energy yield or analyzing losses of the PV systems—especially in high temperature regions.
28 August 2014 in International Journal of Photoenergy
Intrinsic hydrogenated amorphous silicon oxide (i-a-SiO:H) films were used as front and rear buffer layers in crystalline silicon heterojunction (c-Si-HJ) solar cells. The surface passivity and effective lifetime of these i-a-SiO:H films on an n-type silicon wafer were improved by increasing the CO2/SiH4ratios in the films. Using i-a-SiO:H as the front and rear buffer layers in c-Si-HJ solar cells was investigated. The front i-a-SiO:H buffer layer thickness and the CO2/SiH4ratio influenced the open-circuit voltage, fill factor (FF), and temperature coefficient (TC) of the c-Si-HJ solar cells. The highest total area efficiency obtained was 18.5% mV, mA/cm2, and. The TC normalized for this c-Si-HJ solar cell efficiency was −0.301%/°C.
18 May 2010 in Solar Energy Materials and Solar Cells
We have prepared Ag back electrode by screen printing technique and developed MOCVD ZnO/screen printed Ag back reflector for flexible thin film silicon solar cell application. A discontinuity and poor contact interface between the MOCVD ZnO and screen printed Ag layers caused poor open circuit voltage () and low fill factor (FF); however, an insertion of a thin sputtered ZnO layer at the interface could solve this problem. The n type hydrogenated amorphous silicon (a-Si:H) film is preferable for the deposition on the surface of MOCVD ZnO film rather than the microcrystalline film due to its less sensitivity to textured surface, and this allowed an improvement in the FF. The n-i-p flexible amorphous silicon solar cell using the MOCVD ZnO/screen printed Ag back reflector showed an initial efficiency of 6.2% with V, mA/cm2, and FF = 0.58 (1 cm2). The identical quantum efficiency and comparable performance to the cells using conventional sputtered Ag back electrode have verified the potential of the MOCVD ZnO/screen printed Ag back reflector and possible opportunity to use the screen printed Ag thick film for flexible thin film silicon solar cells.
22 June 2014 in International Journal of Photoenergy
This paper reports the preparation of wide gap p-type hydrogenated microcrystalline silicon oxide (p-c-SiO:H) films using a 40 MHz very high frequency plasma enhanced chemical vapor deposition technique. The reported work focused on the effects of the CO2/SiH4ratio on the properties of p-c-SiO:H films and the effectiveness of the films as an emitter layer of crystalline silicon heterojunction (c-Si-HJ) solar cells. A p-c-SiO:H film with a wide optical band gap (E04), 2.1 eV, can be obtained by increasing the CO2/SiH4ratio; however, the tradeoff betweenE04and dark conductivity must be considered. The CO2/SiH4ratio of the p-c-SiO:H emitter layer also significantly affects the performance of the solar cells. Compared to the cell using p-c-Si:H (CO2/SiH4= 0), the cell with the p-c-SiO:H emitter layer performs more efficiently. We have achieved the highest efficiency of 18.3% with an open-circuit voltage () of 692 mV from the cell using the p-c-SiO:H layer. The enhancement in theand the efficiency of the solar cells verified the potential of the p-c-SiO:H films for use as the emitter layer in c-Si-HJ solar cells.