Paolo Sassatelli

Paolo Sassatelli

Auto-generated profile, based on publicly available information

Paolo Sassatelli

Department of Engineering Enzo Ferrari (DIEF), University of Modena and Reggio Emilia, Modena, Italy

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2016 in Wear
Verified
Journal Article
Open access
Giovanni BolelliGiovanni Bolelli
Giovanni Bolelli
LBLutz-Michael Berger
Lutz-Michael Berger
TBT. Börner
T. Börner
Heli KoivuluotoHeli Koivuluoto
Heli Koivuluoto
VMVille Matikainen
Ville Matikainen
Petri VuoristoPetri Vuoristo
Petri Vuoristo
This paper provides a comprehensive characterisation of HVOF- and HVAF-sprayed Cr3C2-25 wt.% NiCr hardmetal coatings. One commercial powder composition with two different particle size distributions was processed using five HVOF and HVAF thermal spray systems. All coatings contain less Cr3C2 than the feedstock powder, possibly due to the rebound of some Cr3C2-rich particles during high-velocity impact onto the substrate. Dry sand-rubber wheel abrasive wear testing causes both grooving and pull-out of splat fragments. Mass losses depend on inter- and intra-lamellar cohesion, being higher (≥70 mg after a wear distance of 5904 m) for the coatings deposited with the coarser feedstock powder or with one type of HVAF torch. Sliding wear at room temperature against alumina involves shallower abrasive grooving, small-scale delamination and carbide pull-outs, and it is controlled by intra-lamellar cohesion. The coatings obtained from the fine feedstock powder exhibit the lowest wear rates (≈5×10-6 mm3/(Nm)). At 400 °C, abrasive grooving dominates the sliding wear behaviour; wear rates increase by one order of magnitude but friction coefficients decrease from ≈0.7 to ≈0.5. The thermal expansion coefficient of the coatings (11.08×10-6 °C-1 in the 30-400 °C range) is sufficiently close to that of the steel substrate (14.23×10-6 °C-1) to avoid macro-cracking

22 May 2015 in International Endodontic Journal
Verified
Journal Article
Closed access
PDF file
CPC. Pirani
C. Pirani
FIF. Iacono
F. Iacono
Luigi GeneraliLuigi Generali
Luigi Generali
PSP. Sassatelli
P. Sassatelli
CNC. Nucci
C. Nucci
CPCarlo Prati
Carlo Prati

11 March 2016 in International Endodontic Journal
Verified
Journal Article
Closed access
PDF file
FIF. Iacono
F. Iacono
CPC. Pirani
C. Pirani
Luigi GeneraliLuigi Generali
Luigi Generali
Giovanni BolelliGiovanni Bolelli
Giovanni Bolelli
PSP. Sassatelli
P. Sassatelli
CPC. Prati
C. Prati

1 March 2018 in Surface and Coatings Technology
Verified
Journal Article
Open access
PSPaolo Sassatelli
Paolo Sassatelli
GBGiovanni Bolelli
Giovanni Bolelli
MGMagdalena Lassinantti Gualtieri
Magdalena Lassinantti Gualtieri
EHEsa Heinonen
Esa Heinonen
MHMari Honkanen
Mari Honkanen
MVMinnamari Vippola
Minnamari Vippola

1 November 2020 in Surface and Coatings Technology
Verified
Journal Article
Closed access
VTVeronica Testa
Veronica Testa
SMStefania Morelli
Stefania Morelli
Giovanni BolelliGiovanni Bolelli
Giovanni Bolelli
BBBeatrice Benedetti
Beatrice Benedetti
PPPietro Puddu
Pietro Puddu
Luca LusvarghiLuca Lusvarghi
Luca Lusvarghi

1 January 2018 in Wear
Verified
Journal Article
Closed access
Giovanni BolelliGiovanni Bolelli
Giovanni Bolelli
MBMarcello Bursi
Marcello Bursi
Luca LusvarghiLuca Lusvarghi
Luca Lusvarghi
TMTiziano Manfredini
Tiziano Manfredini
VMVille Matikainen
Ville Matikainen
Petri VuoristoPetri Vuoristo
Petri Vuoristo