Chuanyang Jia

Chuanyang Jia

Auto-generated profile, based on publicly available information

Chuanyang Jia

School of Civil Engineering and Architecture, Linyi University, Linyi 276000, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 March 2022 in Geofluids
Verified
Journal Article
Open access
PDF file
YJYujing Jiang
Yujing Jiang
SZSunhao Zhang
Sunhao Zhang
Hengjie LuanHengjie Luan
Hengjie Luan
QSQinglin Shan
Qinglin Shan
BLBaocheng Li
Baocheng Li
CJChuanyang Jia
Chuanyang Jia
Understanding the shear properties of joints of rock masses is of great importance for engineering disaster prevention and control. In this paper, a systematic study of the macroscopic shear properties of joints of rock masses with different strengths is carried out using a combination of indoor tests and PFC2D numerical simulations. The results show that (i) the shear stress curve of low-strength rock joints is strain-softening type, while high-strength rock joints are strain-hardening type, and high-strength rock joints are more sensitive to the change of roughness. (ii) With the increase of JRC, the damage mode of different strength rock joints gradually changes from abrasion to abrasion+gnawing, and the damage characteristics of the surface of high-strength rock joints are more significant. (iii) The contact force between particles is mainly concentrated on the joints. At the beginning of shear, the contact force is mainly distributed on the second-order roughness and gradually concentrated on the first-order roughness as the shear progresses. Compared with the low-strength rock joints, the contact force on the high-strength rock joints is larger and more widely distributed. (iv) Due to the change of contact force, the cracks keep expanding and the particle rotation arc keeps changing. The particles with larger rotational arcs are consistent with the location of crack distribution, and the cumulative number of cracks on the joints of high-strength rock is higher. (v) The total input energy and dissipation energy increase continuously with the shear, and the elastic energy tends to increase at the beginning of shear and then starts to decrease and gradually tends to be constant near the peak of shear stress. The total input energy and dissipation energy of the joints of the high-strength rock are larger, while the peak elastic energy of it is smaller.

7 June 2021 in Geofluids
Verified
Journal Article
Open access
PDF file
XCXianzhen Cheng
Xianzhen Cheng
Hengjie LuanHengjie Luan
Hengjie Luan
Yujing JiangYujing Jiang
Yujing Jiang
SZSunhao Zhang
Sunhao Zhang
CJChuanyang Jia
Chuanyang Jia
Despite their frequent natural occurrence and engineering encounter, heterogeneous rock joints (rock joints with different lithological characters on both sides of the joint surface) have been studied much less systematically. To study the shear behavior and failure mechanism of bolted heterogeneous rock joints, laboratory tests were performed on the heterogeneous rock joints having different joint roughness coefficients (JRC) under different anchorage conditions. The results indicate that shear strength increases with the increase of JRC, showing exponential growth. Under the same roughness, the shear strengths of rock joints from large to small are fully grouted, end anchorage, and without anchorage. The mechanical characteristics of the bolt and joint are poorly matched under the end anchorage condition, which is easy to cause these two to be broken one by one. Under fully grouted, the extrusion force caused by the rock bolt will diffuse around the anchorage agent and will not cause partial continuous damage. The surface damage of heterogeneous rock joints increases with the increase of JRC and presents obvious heterogeneous characteristics. The shear dislocation between the blocks under shear load results in the interaction between the bolt and surrounding media. Under the action of shear force, the bolt body produced both axial and transverse deformation, which leads to breakage of anchorage agent and rock mass. Rock bolt has a significant impact on the shear behavior of the anchorage system, and the damage of the rock bolt to rock mass should be considered in rock engineering reinforcement design.

14 December 2020 in Geofluids
Verified
Journal Article
Open access
PDF file
CJChuanyang Jia
Chuanyang Jia
HWHailong Wang
Hailong Wang
HLHaiquan Liu
Haiquan Liu
GZGuibin Zhang
Guibin Zhang
KSKaihua Sheng
Kaihua Sheng
The shaft is the throat of the mine construction, and it is easily disturbed by gushing water, which affects the mine construction progress. Aiming at technical problems under complex hydrogeological conditions in coal mines, such as vertical shaft lining rupture and serious gushing water, single-liquid and double-liquid cement grouting materials are invalid for multiple plugging of gushing water. Combining with geological data to analyze the conditions of the aquifers and water-blocking layer in the shaft, adopting the multifunctional digital electrical method and digital flow measuring instrument can accurately grasp the flow direction and flow velocity and further obtain the aquifer parameters of the main and auxiliary shafts. At the same time, based on the FLAC numerical simulation software, research on the stress, displacement, and plastic failure of the shaft surrounding rock under different water pressures (0.5 times, 1 time, and 2 times the hydrostatic pressure) and comparative analysis of the influence of the water bodies on the shaft surrounding rock are carried out. On this basis, the following are the objectives: (1) research the mechanical properties of polymer chemical material Malisan N and the mechanism of grouting to plugging gushing water and strengthening surrounding rock, (2) formulate the grouting drilling layout and construction technology for the topsoil and bedrock section of the main and auxiliary shafts, and (3) carry out long-term monitoring of the water inflow. The monitoring data showed that the measured water inflow was less than 0.05m3/h after the grouting of the shaft surrounding rock, which achieved the purpose of preventing the shaft linings from rupturing, plugging the gushing water, and stabilizing the aquifer water pressure.