Because of the limitation of mining techniques and economic conditions, large amounts of residual coal resources have been left in underground coal mines around the world. Currently, with mining technology gradually developing, residual coal can possibly be remined. However, when residual coal is remined, caving areas might form, which can seriously affect the safety of coal mining. Hence, grouting technology is put forward as one of the most effective technologies to solve this problem. To study the grouting diffusion in fractured rock mass, this paper developed a visualization platform of grouting diffusion and a three-dimensional grouting experimental system that can monitor the grout diffusion range, diffusion time and grout pressure; then, a grouting experiment is conducted based on this system. After that, the pattern of the grouting pressure variation, grout flow and grout diffusion surface are analyzed. The relationship among some factors, such as the grouting diffusion radius, compressive strength of the grouted gravel, porosity, water-cement ratio, grouting pressure, grouting time, permeability coefficient and level of grout, is quantitatively analyzed by using MATLAB. The study results show that the flow pattern of the grout in fractured porous rock mass has a parabolic shape from the grouting hole to the bottom. The lower the level is, the larger the diffusion range of the grout is. The grouting pressure has the greatest influence on the grouting diffusion radius, followed by the grouting horizon and water-cement ratio. The grouting permeability coefficient has the least influence on the grouting diffusion radius. The grout water-cement ratio has the greatest influence on the strength of the grouted gravel, followed by the grouting permeability. The grouting pressure coefficient has the least amount of influence on the grouting diffusion radius. According to the results, the grouting parameters are designed, and a layered progressive grouting method is proposed. Finally, borehole observation and a core mechanical property test are conducted to verify the application effect. This grouting technology can contribute to the redevelopment and efficient utilization of wasted underground coal resources.

Despite their frequent natural occurrence and engineering encounter, heterogeneous rock joints (rock joints with different lithological characters on both sides of the joint surface) have been studied much less systematically. To study the shear behavior and failure mechanism of bolted heterogeneous rock joints, laboratory tests were performed on the heterogeneous rock joints having different joint roughness coefficients (JRC) under different anchorage conditions. The results indicate that shear strength increases with the increase of JRC, showing exponential growth. Under the same roughness, the shear strengths of rock joints from large to small are fully grouted, end anchorage, and without anchorage. The mechanical characteristics of the bolt and joint are poorly matched under the end anchorage condition, which is easy to cause these two to be broken one by one. Under fully grouted, the extrusion force caused by the rock bolt will diffuse around the anchorage agent and will not cause partial continuous damage. The surface damage of heterogeneous rock joints increases with the increase of JRC and presents obvious heterogeneous characteristics. The shear dislocation between the blocks under shear load results in the interaction between the bolt and surrounding media. Under the action of shear force, the bolt body produced both axial and transverse deformation, which leads to breakage of anchorage agent and rock mass. Rock bolt has a significant impact on the shear behavior of the anchorage system, and the damage of the rock bolt to rock mass should be considered in rock engineering reinforcement design.

To study the shear deformation and failure characteristics of a wellbore and the interaction mechanism with its surrounding rocks induced by a layer slip during natural gas hydrates (NGHs) extraction, this paper conducted a numerical simulation study of wellbore shear induced by a layer slip using ABAQUS software and carried out a laboratory experiment of wellbore shear to verify the accuracy of the numerical model. The results show that the shear force–displacement curves obtained from the laboratory experiments and numerical simulations are consistent with five stages, including the compaction stage, linear stage, plastic stage, strain-softening stage and residual stage. The wellbore shows a “Z”-shaped deformation characteristic after its shear breakage. The shear force of the wellbore is maximum at the shear surface, and it is distributed in an approximate “M” shape along the shear surface. The axial force of the wellbore is small and uniformly distributed in the initial stage of the shear. The wellbore bending moment is minimum at the shear surface, with a value of 0, and it is distributed in a skew–symmetric wave shape along the shear surface. During the shearing, the evolution of the wellbore axial force and shear force can be classified into the distribution pattern along the radial direction on the shear surface and the pattern along the axial direction. The combination of the wellbore axial force and shear force causes the tensile–shear compound failure of the wellbore. During shearing, the wellbore and rock body gradually enter the plastic state with the increase in the shear displacement. When the entire cross-section of the wellbore is in the plastic state, a “necking” phenomenon of the wellbore begins to appear. During the shearing, the frictional dissipation energy and plastic dissipation energy increase constantly. In addition, the elastic strain energy increases to a peak and then decreases to a certain value, which remains unchanged along with the work conducted by the shear force.