A new region-specific Ground Motion Prediction Equation (GMPE) was developed for the North and Central Himalayas purely based on recorded strong motion data. The GMPE was generated using multiple-regression, considering ground acceleration, magnitude, and hypocentral distance. An updated larger dataset was used in the present study, making the new equation applicable to a larger magnitude range of 4.1 to 7.8 and distance range up to 1560 kms, thus overcoming a major limitation of currently available region-specific GMPEs. The new GMPE was validated and observed to predict ground acceleration more accurately with noticeably less residuals as compared to existing GMPEs.
8 March 2018 in International Journal of Geotechnical Engineering
In this paper, a finite element numerical analysis was carried out to study the behaviour of group of piles located on sloping ground using finite element analysis software PLAXIS 3D. A pile of 0.305 m diameter and 9.1 m length was arranged in 3 × 3 group pattern with spacing equal to three times the pile diameter (3D) and was modelled by PLAXIS 3D. The group of piles was embedded into a soil profile consisting of soft to medium-stiff clay and silts underlain by sand. A parametric study was carried out to study the behaviour of group of piles located on sloping ground surface (1V:5H and 1V:3H slopes) and subjected to lateral loads. The effect of slopes on pile capacity, the behaviour of lateral deflections and bending moment profile of front, middle and back rows of group of piles were studied.
Over the past decade, 3D printing in the construction industry has received worldwide attention and developed rapidly. The research and development of cement and concrete products has also become quite well-established over the years, while other sustainable materials receive considerably lower attention in comparison. This study aims to investigate the influence of the two most commonly used sustainable cementitious materials i.e., silica fume and limestone powder, on printability, thermal and mechanical properties of fly ash–Portland cement blends. Ternary blends containing Portland cement, fly ash and silica fume or limestone powder are prepared, whereas phase change material (PCM) is introduced to improve the thermal behavior. Based on the rheological properties and concurrent 3D concrete printing, improved buildability of the modified mixtures is linked to their static yield stress. Anisotropic mechanical properties are observed for 3D printed specimens, while cast specimens exhibit a maximum 41% higher compressive strength due to better material compaction. It is clear from the results that addition of silica fume and limestone powder ranged from 5% to 10%, reducing the anisotropic mechanical properties (maximum 71% and 68% reduction in anisotropic factor, respectively) in the printed specimens. The PCM addition ranged from 5% to 10% and improved thermal performance of the mixtures, as measured by a decrease in thermal conductivity (9% and 13%) and an increase in volumetric heat capacity (9% and 10%), respectively. However, the PCM-containing mixtures show around 29% reduction in compressive strength, compared to the control specimen, which necessitates new material design considering matrix strengthening methods.
Existing Ground Motion Prediction Equations (GMPE) in practice for North East India have been developed using limited or simulated datasets of recorded ground motions. The current study presents the development of a new GMPE based on a well-established model considering actual recorded ground motion data comprising of acceleration, magnitude, and hypocentral distances. A larger dataset with magnitudes ranging from 4.2 to 6.9 and up to 640 kms, with a total of 204 recordings is used in non-linear multiple-regression. The newly developed GMPE could predict ground acceleration realistically over larger ranges of distance and magnitudes, compared to existing GMPEs.
3 September 2021 in Bulletin of Engineering Geology and the Environment
Current study illustrates the effect of interference on closely spaced square footings in loose, medium and dense sand beds using experimental and numerical studies. Experimental results suggest that with increase in the clear spacing interference decreases and after 2B spacing between the footings, the interference effects are almost zero, where B is width of the footing. The interference effect is quantified as Interference Factor, IF and is defined as ratio of ultimate bearing pressure of an interfering footing to that of an isolated footing. Maximum Interference Factor of about 1.25 is observed in dense sand. Interference is attributed to increase in confinement pressure due to the interaction between the failure zones of interfering footings. To this end, FLAC 3D (Fast Lagrangian Analysis of Continua in 3 Dimensions) models were developed and numerical simulations have been carried out. The effects of frictional angle and dilation on interference factor are presented.