30 August 2025 in Neft i Gaz
WKWest Kazakhstan Agrarian and Technical University named after Zhangir Khan
West Kazakhstan Agrarian and Technical University named after Zhangir Khan
The article considers the scientific and technological foundations and features of industrial application of the diesel fuel hydrotreating process. The relevance of the study is explained by the increasing environmental requirements for diesel fuel due to the increase in the number of transport modes. The main goal is to obtain high-quality, stable and environmentally friendly diesel fuel by reducing the amount of sulfur-, nitrogen- and oxygen-containing compounds. The hydrotreating process is based on the catalytic method. Molybdenum-cobalt and molybdenumnickel systems embedded in highly porous aluminum oxide were used as catalysts. Diesel fractions with boiling limits of 164–351 °C were used as raw materials. As a result of studies conducted under conditions of high pressure and temperature in a hydrogen environment, it was found that up to 95% of sulfur compounds are eliminated in diesel fuel, and the sulfur content in the finished product does not exceed 10 ppm. The physicochemical properties of the resulting hydrogenate fully comply with the requirements of GOST R 55475-2013. Key indicators: freezing point -48 °C, density 784.5–800 kg/m³, flash point 30 °C, sulfur content < 10 ppm, content of mechanical impurities and water below the norm. This quality allows the fuel to be used in arctic conditions and ensures reliability and long service life of engines. In addition, hydrotreating is not limited to sulfur removal, but also improves the color, smell and stability of the fuel, increases the cetane number. This increases the wear resistance of diesel engines, reduces the formation of carbon residues and reduces the amount of harmful gases emitted into the environment. The results of the studies confirm the importance of hydrotreating technology for improving the quality of diesel fuel and obtaining products that meet international environmental standards.
15 April 2022 in Neft i Gaz
The paper analyzes the factors influencing the development of high-quality and cost-effective oil and gas reserves in the region (assessment, design). In order to operate wells, directions for calculating the size of reserves have been found. The scientific and technical trends of their (wells) development are considered. A comprehensive analysis of complex surveys was carried out at well No32 of the Chinarevskoye oil and gas condensate field, located in the southern section of the region. Hydrodynamic studies were carried out by interpreting the pressure recovery curve (PRC) to determine reservoir pressure, reservoir properties and the state of the bottomhole zone. These studies confirmed the low porosity properties of the reservoir: permeability - 0.004 mkm2 , conductivity - 0.056 mkm2 *m, hydraulic conductivity - 0.055 mkm2 *m/MPa*s. The skin factor varied in the range from - 0.92 to 18.4, which indicates a deterioration in the state of the bottomhole formation zone. Reservoir pressure dynamics (reduced to WOC) according to hydrodynamic studies showed that in the deposit, as the reservoir is withdrawn, there is a decrease in reservoir pressure. As of October 2019, according to the pressure build-up data, the formation pressure in well 32 (at the VNK level) is 38 MPa. Well 32 during the analyzed period (5 months) worked in three modes (from July to September 2019 with a washer with a diameter of 6 mm, from the end of September with a washer with a diameter of 8 mm, in October - 10 mm). At the same time, with an increase in the washer diameter to 8 and 10 mm, the downhole working pressure sharply decreased from 25 to 11 MPa and the static bottomhole pressure from 37.5 to 29.7 MPa. During the analyzed period, the well worked with a bottomhole pressure below the saturation pressure of oil with gas. The average gas-oil ratio was 757 m3/m3.
30 September 2026 in Химическая технология
This paper examines the feasibility of producing liquid glass using a natural siliceous raw material - flake from the Taskala deposit, located in the West Kazakhstan region of the Republic of Kazakhstan. Physicochemical analyses of the source material were performed, determining its chemical and mineralogical composition, silica content, and clay content. Chemical composition revealed a SiO2 content of 70-78%, which meets the raw material requirements for liquid glass production. The process of alkaline treatment of opoka using 20% solutions of sodium and potassium hydroxide has been studied. The temperature and time parameters affecting the completeness of silica dissolution have been studied. It has been established that at a temperature of 95-98 °C and a duration of 2-3 hours, the best result is achieved in terms of the yield of liquid glass with a silicate module within the regulatory limits when the raw material: alkali ratio is 1:2. Alkaline treatment of flasks using 20% sodium and potassium hydroxide solutions was studied. Temperature and time parameters influencing the completeness of silica dissolution were examined. It was found that a temperature of 95-98°C and a duration of 2-3 hours with a raw material: alkali ratio of 1:2 yielded the best liquid glass with a silicate modulus within the specified limits. Thus, the opoka from the Taskalinsky deposit can be effectively used as a raw material for the production of liquid glass, which has been confirmed by laboratory tests and a feasibility study of the process.
30 September 2025 in Вестник КазУТБ
Шыны – құрылыс саласы мен күнделікті тұрмыста кеңінен қолданылатын маңызды материалдардың бірі. Шыны бұйымдарына деген сұраныс жыл сайын артып келеді, бұл өз кезегінде шыны өнеркәсібінің өндіріс көлемін ұлғайтуға және олардың сапасын сақтауға жетелейді. Шыны өндірісіндегі ғылыми-техникалық жетістіктер оның қолдану аясын кеңейтуде үлкен рөл атқарды. Өндірудің жаңа әдістері мен қолданылып жүрген технологиялық процестерді жетілдіру тәсілдері пайда болып, шыны қолданудың жаңа аймақтары ашыла бастады. Өнімнің химиялық құрамын өзгерту арқылы әртүрлі шыны түрлері жасалды. Осы орайда, әртүрлі қасиеттері бар шыныларды алу әдістерін зерттеу маңызды болып табылады. Түрлі бұйымдарды өндіру үшін түсті шыны композициясын зертханалық жағдайда дайындап, оның физика-химиялық қасиеттерін зерттеу жүргізілді. Зерттеу нәтижелері бойынша алынған түсті шынының сәндік мақсаттарда қолдануға болатындығы анықталды.
30 March 2022 in Chemical Journal of Kazakhstan
The last decades of human life were marked by a sharp increase in various technological processes in the economy and everyday life. This also affected the construction industry. In accordance with this, construction is one of the priorities of the national economy and meets the basic needs of the population. In work the technology of reception of a building brick with use of a waste of polymers and rubber products is considered. Polymer bricks were obtained for processing household waste. The following properties of polymer bricks were studied: short-term strength, moisture absorption, water resistance property, heat conductivity, sound insulation. It is proved that after the addition of polymers and rubber products to the brick, the performance indicators of the brick improved.