This article presents a single-loop third-order discrete-time delta-sigma modulator (DTDSM) with a 4-bit second-order noise shaping successive approximation register (NS SAR) quantizer. To realize an aggressive noise transfer function (NTF), a novel Finite Impulse Response (FIR) filter is embedded in the NS SAR. As employing a flipped voltage follower (FVF), which offers unity gain instead of an open loop dynamic amplifier, the proposed FIR filter is sharp and insensitive to process, voltage, and temperature (PVT) variation. Fabricated in a 65-nm 1P9M CMOS technology, the prototype DTDSM consumes 44 $\mu$ W when operating at a 1.2-V supply voltage and a sampling rate of 2.4 MS/s. It achieves a peak Schreier figure of merit (FoM) of 177.9 dB with a signal-to-noise and distortion-ratio (SNDR) of 91.3 dB at an oversampling ratio (OSR) of 64.
1 August 2019 in IEEE Transactions on Circuits and Systems II: Express Briefs
The brief presents a CMOS analog frontend ( AFE ) IC with high input impedance low input-referred noise, which for wearable electrocardiogram monitoring. The IC has three main parts, pseudo-differential chopper-stabilized instrumentation amplifier, switched capacitor filter, and low-power continuous--time ∑Δ modulator. The pseudo-differential structure with chopper stabilization improves the input impedance, input--referred noise and chip area. Notably, we propose a new type of negative capacitor circuit to further boost the input impedance. Furthermore, the auto-zero technique is applied to the ripple reduction loop for suppressing the second harmonic ripple and maintain operation throughout the loop cycle. A dc servo loop suppresses the electrode dc offset. In 0.18 μm CMOS process, the proposed AFE IC occupies an active area of 0.99 mm2, consumes 5.8/46.6 μA from a 1.8 V supply, and achieves an input impedance above 2 GΩ, a CMRR of 102 dB and a PSRR of 72 dB.
22 January 2025 in IEEE Transactions on Circuits and Systems I: Regular Papers
This article reports a high acoustic overload point (AOP) single-ended digital MEMS microphone system. For audio applications in high sound pressure environments, a high AOP MEMS microphone is required. The nonlinearity of MEMS microphone is contributed by the MEMS sensor and the signal path of the readout ASIC. For the MEMS sensor with fixed sensitivity, the low analog supply voltage in the readout ASIC is the main limitation to achieve high AOP. To address this challenge, a single-ended digital MEMS microphone system with a self-adaption loop (SAL) is proposed. The SAL automatically adjusts the gain of the analog front end and the digital back end by detecting the input signal, breaking the limitation of the analog supply voltage on the AOP of the system. Besides, the proposed system features an always-on characteristic, and the power consumption is scalable. A prototype is realized in a $0.153~\mu $ m CMOS process, performing 67.34 dB-A SNR with an AOP of 132 dB SPL, consuming $738~\mu $ A at 2.4 MHz sampling rate and 1.5-V supply voltage.
26 November 2025 in IEEE Transactions on Circuits and Systems I: Regular Papers
For wearable applications, the small size low noise MEMS accelerometer with high efficiency is required. However, the sensitivity of the MEMS sensor reduces with the sensor size scaling down, leading to deterioration of the circuit noise. To meet this challenge, the interface circuit with high-voltage pulse excitation (HVPE) and active noise cancelation readout technique is proposed. The HVPE reduces the circuit noise and the wire resistance noise significantly without introducing additional electrostatic force to the sensor. The drift and mismatch problems of the HVPE are addressed by three specific correction circuits. The power efficiency of the system is optimized by the capacitance-to-voltage converter with active noise cancellation and pulse current supply. The propose HVPE technique is demonstrated in an interface IC fabricated by $0.18\mu $ m BCD process and tested with a small size MEMS accelerometer (0.64mm2/axis). The measurement result shows that this IC has achieved a noise floor of $32.5\mu $ g/$\surd $ Hz with 2kHz bandwidth and $80\mu $ W power consumption.
17 March 2026 in IEEE Journal of Solid-State Circuits
The always-on drive loop with low power is a key enabler for intelligent inertial measurement unit (IMU). One of the key design challenges of the always-on drive loop is the trade-off between the always-on power consumption and the wake-up time. To meet this challenge, the burst-mode always-on drive loop composed of the burst-mode automatic gain control (AGC) loop and burst-mode phase-locked loop (PLL) was reported, which can theoretically achieve the sub-$\mu $ A always-on power. However, the parasitic relaxation oscillation (PRO) makes it vulnerable to temperature variation. To solve this problem the duty-cycle automatic optimization (DAO) technique is proposed, which maintains the gyroscope in semistable oscillation to enhance the thermal stability. The propose technique is demonstrated in an interface IC fabricated by $0.18~\mu $ m BCD process and tested with a 3-axis MEMS gyroscope. The measurement result shows that this system has achieved $0.8~\mu $ A always-on power consumption, 2.8ms wake-up time, and ±5% wake-up time stability from $- 40~^{\circ }$ C to $85~^{\circ }$ C.
17 March 2026 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper proposes the nested frequency-phase-division-multiplexing (Nested FPDM) based analog-front-end (AFE) for multi-channel signal recording of the bio-potential. The AFE employing the nested FPDM structure significantly reduces the crosstalk. In the multi-channel signal recording AFE, there are two design challenges: 1) noise performance limitation due to the large parasitic capacitance in the front-end instrumentation amplifier, 2) significant chip area consumption due to the large capacitance in the back-end programmable gain amplifier. To address the challenges, the operational amplifier capacitance matching technique and the miller-effect-reduction technique are employed. The proposed 4-channel nested FPDM-AFE is fabricated in a commercial $0.18\mu $ m BCD process, consuming $17.7~\mu $ A at a single 1.8-V supply voltage. Compared to other similar reported multiplexing bio-potential recording AFEs, this work achieves the best crosstalk of −89.2 dB, a competitive power efficiency in terms of NEF (4.29) and a compact chip area of 0.118 mm2/channel.