Han-Gon Ko

Han-Gon Ko

Auto-generated profile, based on publicly available information

Han-Gon Ko

ONE semiconductor, Suwon, South Korea

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 October 2021 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
KPKwanseo Park
Kwanseo Park
MSMinkyo Shim
Minkyo Shim
HKHan-Gon Ko
Han-Gon Ko
BNBorivoje Nikolic
Borivoje Nikolic
DJDEOGKYOON JEONG
DEOGKYOON JEONG
This article presents design techniques for a continuous-rate reference-free clock and data recovery (CDR) circuit employing a stochastic frequency–phase detector (SFPD). By taking a histogram-based design methodology, optimal weights for both frequency and phase detection are obtained by utilizing the same information as the Alexander phase detector. The design methodology is inductive and stochastic, distinguished from the conventional, deductive, and procedural methods. To verify a robust operation, the effects of varied data patterns, noise, and channel loss are examined, together with the avoidance of harmonic locking. In addition, a consideration of a sample window is analyzed by fast Fourier transform (FFT) simulation. Fabricated in 40-nm low-power (LP) CMOS technology, the proposed CDR circuit achieves a capture range from 6.4 to 32 Gb/s and a lock time of less than $11 \mu \text{s}$ . The measured frequency acquisition behavior shows that harmonic locking is avoided with a seamless transition to the fundamental mode. The CDR circuit tested over a 10-dB loss channel achieves a bit error rate (BER) less than 10 −12 and energy efficiency of 0.96 pJ/b.

15 February 2018 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
SCSung-Yong Cho
Sung-Yong Cho
SKSungwoo Kim
Sungwoo Kim
MCMin-Seong Choo
Min-Seong Choo
HKHan-Gon Ko
Han-Gon Ko
JLJinhyung Lee
Jinhyung Lee
DJDEOGKYOON JEONG
DEOGKYOON JEONG
A 2.5-5.6 GHz low-phase-noise subharmonically injection-locked sub-sampling all-digital phase-locked loop with a dual-edge complementary switched injection technique is presented. While previously reported injection-locked phase-locked loops (ILPLLs) require additional circuitry for resolving a phase alignment mismatch between the PLL loop and injection path, the presented ILPLL exhibits a simplified architecture owing to the proposed injection technique and sub-sampling bang-bang phase detector (SSBBPD). Because the proposed injection technique exploits dual-edge injection, we analyze the performance impact of dual-edge injection when inaccurate injection timing occurs. This paper also offers an analysis of the injection technique based on the charge transfer and derives the realignment factor of the injection. With the proposed injection technique and the direct connection of the digitally controlled oscillator (DCO) clock to the SSBBPD, the timing mismatch between the PLL loop and injection path becomes insensitive to voltage and temperature drift. The proposed ILPLL prototype is fabricated in a 65-nm CMOS process and achieves a 168-fs integrated rms jitter over 1 kHz to 40 MHz at a 5-GHz output frequency with 156.25-MHz reference clock while consuming 15.4 mW with an active area of 0.06 mm 2 .

19 March 2019 in IEEE Access
Verified
Journal Article
Open access
HKHan-Gon Ko
Han-Gon Ko
Woorham BaeWoorham Bae
Woorham Bae
GJGyu-Seob Jeong
Gyu-Seob Jeong
DJDEOGKYOON JEONG
DEOGKYOON JEONG
This paper presents the reference spur reduction techniques for an analog phase-locked loop (PLL). A simple leakage compensation loop is proposed, which cancels the leakage current of the PLL loop filter with a negligible power overhead. This leakage compensation loop senses the leakage current of the loop filter from the up and down pulse widths in the steady state, and compensates for the charge loss due to the leakage current. A systematic approach for the reference spur reduction is also proposed. Since a PLL operates as a band pass filter in the frequency domain, the reference spur can be filtered out by cascading the PLLs. The optimization technique for the cascaded PLLs is presented that minimizes the reference spur without degrading the phase noise performance. The proposed techniques are verified using an 800-MHz PLL chip fabricated in 65-nm CMOS process. The prototype PLL achieves the reference spur of -68.57 dBc, while the conventional charge-pump PLL without the proposed spur reduction techniques achieves -42.83 dBc.

30 October 2018 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
MCMin-Seong Choo
Min-Seong Choo
HKHan-Gon Ko
Han-Gon Ko
SCSung-Yong Cho
Sung-Yong Cho
KLKwangho Lee
Kwangho Lee
DJDEOGKYOON JEONG
DEOGKYOON JEONG
An injection-locked phase-locked loop (ILPLL) which continuously tracks the injection timing to achieve improved jitter performance is presented. When the injection timing is not precisely matched with the edges of the oscillator clock, the performance of ILPLL such as jitter and reference spur degrades significantly. To find an optimum injection timing, a calibration technique is proposed that continuously monitors the error information from the bang-bang phase and frequency detector (BBPFD) when the injection of the reference clock is intentionally omitted every other cycle. The timing calibrator enables a robust ILPLL operation over the process, voltage, and temperature (PVT) variations. The proposed ILPLL fabricated in 28-nm CMOS technology occupies 0.03 mm2 and consumes 5.65 mW at 5 GHz with 0.9-V supply voltage. The measured jitter integrated from 1 kHz to 40 MHz is 152 fs, and the spur levels at the reference and 2nd subharmonic are -62 dBc and -53 dBc, respectively.

28 October 2021 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
YSYeonggeun Song
Yeonggeun Song
HKHan-Gon Ko
Han-Gon Ko
CKChanghyun Kim
Changhyun Kim
DJDEOGKYOON JEONG
DEOGKYOON JEONG
This brief presents an all-digital PLL (AD-PLL) for a DDR5 registering clock driver (RCD) with a self-biased supply-noise-compensation (SNC) technique. By combining two Nagata current sources that have opposite dependency on supply variations, it offers a constant current to a ring oscillator over a wide range of supply voltage. Thereby, the dynamic voltage droop due to variations in workload is compensated while a voltage margin for mass production is improved. Since the SNC technique operates independently of the PLL loop bandwidth without using feedback, the proposed AD-PLL is free from the stability problem associated with bandwidth overlapping. Quantitative analyses on static and dynamic characteristics of the proposed SNC technique and relevant design considerations are addressed. Fabricated in the 28-nm CMOS technology, the AD-PLL occupies an active area of 0.06 mm 2 and consumes 12.1 mW at 3.0 GHz with a 1.1 V supply voltage. The power-supply-noise-attenuation (PSNA) is measured as 40 dB and the integrated rms jitter of 271 fs is observed.

25 March 2021 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
MCMin-Seong Choo
Min-Seong Choo
SKSungwoo Kim
Sungwoo Kim
HKHan-Gon Ko
Han-Gon Ko
SCSung-Yong Cho
Sung-Yong Cho
KPKwanseo Park
Kwanseo Park
DJDEOGKYOON JEONG
DEOGKYOON JEONG
Although an injection-locked oscillator (ILO) can offer excellent jitter performance on average, its intense phase modification at a given injection rate inevitably degrades spur performance, unless injection timing is carefully controlled. This work investigates a behavioral model of the ILO with digital control of a bang-bang phase detector (BBPD) on a discrete-time domain, a quantitative analysis on the dynamics of the digital injection-locked clock multiplier (ILCM) is provided. Adjusting frequency error between the free-running oscillator and the injection signal is crucial to obtain better spur performance. However, the timing offset caused by the device mismatches hinders it from being correctly compensated. Therefore, we investigate the effect of timing offset (or mismatch) between the replica cells and BBPD and then propose the time-division dual calibration (TDDC) to reduce the discrepancies. In addition, three-stage replica cells are chosen to achieve a robust operation in the phase generating aspect. By removing the residual phase offset using multiple delay cells, the optimum locking point is guaranteed.