This paper describes the design of a 10 GHz phase-locked loop (PLL) for a 40 Gb/s serial link transmitter (TX). A two-stage ring oscillator is used to provide a four-phase, 10 GHz clock for a quarter-rate TX. Several analyses and verification techniques, ranging from the clocking architectures for a 40 Gb/s TX to oscillation failures in a two-stage ring oscillator, are addressed in this paper. A tri-state-inverter-based frequency-divider and an AC-coupled clock-buffer are used for high-speed operations with minimal power and area overheads. The proposed 10 GHz PLL fabricated in the 65 nm CMOS technology occupies an active area of 0.009 mm 2 with an integrated-RMS-jitter of 414 fs from 10 kHz to 100 MHz while consuming 7.6 mW from a 1.2-V supply. The resulting figure-of-merit is -238.8 dB, which surpasses that of the state-of-the-art ring-PLLs by 4 dB.
29 April 2020 in IEEE Journal of Solid-State Circuits
In this article, a 1.62-to-10.8-Gb/s video interface receiver with jointly adaptive equalization is presented. Sign-sign least-mean-squares (SSLMS) algorithm is applied to adaptation for not only a decision feedback equalizer (DFE) but also a continuous-time linear equalizer (CTLE) to unify the adaptation methods. This approach facilitates concurrent adaptation that results in short adaptation time and also reduces the extra hardware and power consumption. An average value of fourth- and fifth-post-cursors is used as an indicator for CTLE adaptation, and the validity is substantiated by numerical analysis and simulation. Furthermore, the concept of a biased data-level reference (dLev) is proposed and analyzed to alleviate insufficient adaptation of the SSLMS algorithm in the presence of pre-cursor inter-symbol interference (ISI). The proposed dLev is acquired by simply adjusting up and down ratios of the dLev update equation. The prototype test chip is implemented in 65-nm CMOS technology and occupies an active area of 0.174 mm². The proposed adaptive equalizers compensate for the channel loss of up to 34 dB at 10.8 Gb/s. Total power consumption of the receiver is 37.2 mW at 10.8 Gb/s, and the figure of merit (energy efficiency per channel loss at Nyquist frequency) of 0.1 pJ/b/dB is achieved.
3 September 2018 in IEEE Journal of Solid-State Circuits
A single-loop referenceless clock and data recovery (CDR) with a compact frequency acquisition scheme is presented. A bang-bang phase-frequency detector (BBPFD) is proposed that tracks the frequency difference by detecting the drift direction of the non-return to zero bit stream with respect to the multi-phase clock and generates UP/DN output signals accordingly. When frequency locked, the BBPFD is degenerated into the conventional bang-bang phase detector (BBPD). The UP/DN output signals from the BBPFD are thus connected directly to the loop filter, thereby reducing the acquisition time without any loss of cycles. The effect of sampling phase mismatch is analyzed, and the capture range is calculated. In addition, the frequency acquisition time is analytically derived and verified by simulation. The proposed CDR has been implemented in a 65-nm CMOS process and occupies an active area of 0.047 mm 2 . The measured capture range is 6.7-11.2 Gb/s, and the frequency acquisition time is less than 2.19 μs. The proposed CDR achieves error-free operation (BER <; 10 -12 ) for PRBS31 pattern and consumes 22.5 mW at 10 Gb/s.
26 October 2020 in IEEE Journal of Solid-State Circuits
A continuous-rate referenceless clock and data recovery (CDR) circuit with an unlimited frequency acquisition capability is presented. The proposed frequency detector (FD) is derived from a multi-phase oversampling FD. Through accurate analysis of the root causes limiting the capture range, the extension techniques are proposed and digitally implemented by a small hardware overhead. The FD achieves the unlimited frequency detection capability and exhibits robust operation regardless of the initial clock frequency. The effect of the quadrature error is analyzed and verified by simulation. In addition, a frequency lock detector is implemented to control the loop gain for fast frequency acquisition. The prototype CDR circuit was designed and fabricated in a 65-nm CMOS process, occupying an active area of 0.045 mm². The CDR circuit achieves a capture range from 4 Gb/s to 20 Gb/s, which is limited only by the oscillator operating range. The worst case acquisition time is 25 μs with a PRBS31 pattern. The CDR circuit achieves a BER less than 10⁻¹² and an energy efficiency of 1.87 pJ/b.
15 September 2021 in IEEE Journal of Solid-State Circuits
This article presents a 200-Gb/s pulse amplitude-modulation four-level (PAM-4) and 100-Gb/s non-return-to-zero (NRZ) transmitter (TX) in 28-nm CMOS technology. To achieve the target data rate, the output bandwidth and swing of the proposed TX are optimized by minimizing the output capacitance of the 4:1 multiplexer (MUX) and driver stage with pull-up current sources and adopting a fully reconfigurable 5-tap feed-forward equalizer (FFE). The key circuit includes a segmented 8:4 MUX and 4:1 MUX/driver, a thermal encoder and retimer, and a flexible clock distribution network. Using the layout generated with Berkeley Analog Generator (BAG), the proposed TX achieves an eye opening with >52.9-mV eye height, 0.36 UI eye width, >98% RLM, and 4.63 pJ/b at 200-Gb/s PAM-4 signaling under >6-dB channel loss at 50 GHz, demonstrating the highest data rate achieved using a planar process.
13 October 2021 in IEEE Journal of Solid-State Circuits
This article presents design techniques for a continuous-rate reference-free clock and data recovery (CDR) circuit employing a stochastic frequency–phase detector (SFPD). By taking a histogram-based design methodology, optimal weights for both frequency and phase detection are obtained by utilizing the same information as the Alexander phase detector. The design methodology is inductive and stochastic, distinguished from the conventional, deductive, and procedural methods. To verify a robust operation, the effects of varied data patterns, noise, and channel loss are examined, together with the avoidance of harmonic locking. In addition, a consideration of a sample window is analyzed by fast Fourier transform (FFT) simulation. Fabricated in 40-nm low-power (LP) CMOS technology, the proposed CDR circuit achieves a capture range from 6.4 to 32 Gb/s and a lock time of less than $11 \mu \text{s}$ . The measured frequency acquisition behavior shows that harmonic locking is avoided with a seamless transition to the fundamental mode. The CDR circuit tested over a 10-dB loss channel achieves a bit error rate (BER) less than 10 −12 and energy efficiency of 0.96 pJ/b.