1 May 2015 in Plasma Sources Science and Technology
21 April 2016 in Journal of Applied Physics
High-power impulse magnetron sputtering (HiPIMS) is used to deposit amorphous carbon thin films with sp3 fractions of 13% to 82%. Increasing the pulse length results in a transition from conventional HiPIMS deposition to a “mixed-mode” in which an arc triggers on the target surface, resulting in a large flux of carbon ions. The films are characterized using X-ray photoelectron spectroscopy, Raman spectroscopy, ellipsometry, nanoindentation, elastic recoil detection analysis, and measurements of stress and contact angle. All properties vary in a consistent manner, showing a high tetrahedral character only for long pulses, demonstrating that mixed-mode deposition is the source of the high carbon ion flux. Varying the substrate bias reveals an “energy window” effect, where the sp3 fraction of the films is greatest for a substrate bias around −100 V and decreases for higher or lower bias values. In the absence of bias, the films' properties show little dependence on the pulse length, showing that energetic ions are the origin of the highly tetrahedral character.
9 October 2015 in Journal of Physics D: Applied Physics
Tetrahedral amorphous carbon films with an sp 3 content of 80% have been produced by high power impulse magnetron sputtering (HiPIMS) operating in a mixed sputtering/arc mode. In this mode, short-lived cathode spots form in the magnetic racetrack and produce large numbers of carbon ions. The spots move rapidly, inhibiting the formation of macroparticles. An argon pressure below 2.5 mTorr was critical for obtaining films with high sp 3 content, high stress, large Tauc gap and symmetrical Raman spectra, and all four quantities were strongly correlated.
1 March 2016 in Applied Surface Science
12 May 2016 in Journal of Physics D: Applied Physics
Instabilities in reactive sputtering have technological consequences and have been attributed to the formation of a compound layer on the target surface ('poisoning'). Here we demonstrate how the duty cycle of high power impulse magnetron sputtering (HiPIMS) can be used to control the surface conditions of Hf and Nb targets. Variations in the time resolved target current characteristics as a function of duty cycle were attributed to gas rarefaction and to the degree of poisoning of the target surface. As the operation transitions from Ar driven sputtering to metal driven sputtering, the secondary electron emission changes and reduces the target current. The target surface transitions smoothly from a poisoned state at low duty cycles to a quasi-metallic state at high duty cycles. Appropriate selection of duty cycle increases the deposition rate, eliminates the need for active regulation of oxygen flow and enables stable reactive deposition of stoichiometric metal oxide films. A model is presented for the reactive HIPIMS process in which the target operates in a partially poisoned mode with different degrees of oxide layer distribution on its surface that depends on the duty cycle. Finally, we show that by tuning the pulse characteristics, the refractive indices of the metal oxides can be controlled without increasing the absorption coefficients, a result important for the fabrication of optical multilayer stacks.
14 February 2024 in Journal of Vacuum Science & Technology A
IFIvan Fernandez-Martinez
+1
The deposition of gold-colored titanium nitride films without applying substrate heating is of significant interest due to the increasing demand for decorative coatings on temperature-sensitive three-dimensional substrates. Here, the energetic impact of Nb1+ ions during the deposition of TiN was achieved within a bipolar high-power impulse magnetron sputtering discharge operating on a Nb target. A separate titanium target was operated with direct current magnetron sputtering in the same reactive argon–nitrogen mixture. This process aimed to achieve a dense titanium nitride with the assistance of the niobium ion bombardment. The niobium controlled the phase formation and structure of the resulting Nb-containing TiN coating without needing external heating. The niobium ion bombardment during deposition increases the density of the titanium nitride coatings, promoting the formation of the cubic phase favored for its gold color and excellent mechanical and tribological properties, including HF1-level adhesion. Energy-selective mass spectrometer investigations revealed an increase in the flux and the energy of titanium ions due to momentum transfer from niobium ions to titanium neutrals in the plasma generated between the targets and the substrate. The approach introduced here paves the way for the formation of the cubic phase of Nb-doped TiN films without external heating, producing coatings with combined decorative and protective properties.