Pneumatic and tendon‐driven actuators are widely used in soft robotic glove design. Tendon‐driven robotic gloves are generally better in controllability, dexterity, and force output, but they are less comfortable than pneumatic ones. Most soft gloves focus on only one actuation mode where either motor‐driven tendon or pump‐driven pneumatic transmission is used. Herein, a double‐acting soft actuator (DASA) that provides both tendon‐driven flexion and pneumatic extension of fingers by a single motor is presented. This is achieved by a smart pulley and bellow system. The kinematic model of the tendon‐driven flexion and the torque model of the fabric‐based pneumatic extension actuator (FPEA) are developed to analyze the DASA performance. The bending angle of the index finger actuated by the tendon and the FPEA extension torque of a joint are characterized by experimental studies. A cycle test of the DASA is conducted 3000 times, demonstrating its high repeatability. A prototype soft glove (68 g) based on the proposed DASA with a control box (835 g) is fabricated to demonstrate finger flexion and extension assistance. Based on electromyography signals, the performance of the robotic glove is evaluated by a squeezing sponge test.
Previous research on wearable robotics focused on developing actuation mechanisms while overlooking influences of skin movement. During finger flexion, skins on the opisthenar and finger back are stretched. Impeding such skin movement will obstruct normal finger motions. In this research, a statistical study on skin movement is proposed and conducted to quantify skin movement on human hands. Results of 30 subjects (15 men and 15 women) reveal that skin at the finger back extends by an average of 29.3 ± 7.2% in fist clenching. Based on this study, design guidelines for robotic gloves are proposed, and nominal strain values at different hand regions are tabulated for references in robotic glove design. To explore the influence of skin movement on wearable robotics, an elastomer-constrained flat tube actuator is proposed based on which two prototype robotic gloves are developed: one with an ergonomic strap interface that has small constraint to skin motion, and the other based on the commonly used fabric glove that is supposed to have large constraint to skin motion. With the same power input to the robotic gloves, the strap-based design achieves a finger motion range of 2.5 times and a gripping force of 4.3 times that of the conventional fabric glove.
In wearable robotics, soft actuation principles have been increasingly explored and tested due to their safety and comfort in human–robot interactions. Herein, a braided flat‐tube artificial muscle (BFAM) is presented. BFAMs are fabricated by braiding cotton threads together with an inexpensive lay‐flat tube (LFT) in a specific conform‐to‐LFT weaving method. They generate uniaxial contractions when powered by compressed fluids. The basic structure and working mechanism of the proposed BFAM are explained, and a quasistatic model is also developed. A comparison with other fluidic driven soft actuators is made and tabulated. Based on experimental studies, the proposed BFAM can contract close to 30% and yield force outputs more than 150 times their weight at an air pressure of 0.12 MPa. BFAM can be braided with multiple layers of flat tube without large increase of size. Experimental studies have shown that more layers of flat tube give a larger strain and output force up to four layers, beyond which layer increase does not yield visible improvement in strain and output force. Finally, potential applications of BFAM to arm joint actuations are illustrated to show its easy fitting to wearable robotics.
1 April 2025 in IEEE/ASME Transactions on Mechatronics
Haptic perception is essential for robotic grippers performing delicate handling tasks, yet designing a tactile sensor that is both low-cost and high-performance remains a challenge. This article addresses this issue by developing an optical blocking structure (OBS) sensor for tactile perception in robotic grippers. The OBS sensor is characterized by its ease of fabrication, cost-effectiveness (with a unit cost of $1.45), and high-performance metrics, including a maximum sensitivity of approximately 2.18 V/N, a wide pressure response range (>4 N), high resolution (0.009 N), a fast response time (15 ms), and a minimal dead zone (around 0.026 N). Experimental results demonstrate that a robotic gripper equipped with the OBS sensor can effectively detect object hardness, surface texture, and perform delicate force control tasks. Additionally, the OBS sensor exhibits high scalability. It can be configured into various array forms to enhance the gripper's sensing capabilities based on its structural characteristics. Validation experiments confirm that robotic grippers integrated with 2 × 2 and 1 × 6 array configurations of the OBS sensor can accurately detect multiple contact positions and forces. Consequently, the OBS sensor offers a straightforward and effective solution for enhancing tactile sensing in robotic grippers.
Mimicking invertebrates, soft robots tend to control each of their body joints to achieve the desired shape changes and movements to accomplish different tasks. Shape‐memory alloy (SMA) is a common actuation material but needs to be designed into specific shapes to disperse local strains. In this article, a dedicated configuration of SMA strips is introduced for soft robotic body joint manipulation and morphing. Inspired by the Möbius strip, the proposed SMA torsion strip (STS) can meet the requirements of both large deformation and large force output desirable for robotic applications. Compared to conventional morphing methods, the STSs can supply considerable torque output over a wide range of bending angles to freely chosen body joints. Therefore, both pattern‐to‐pattern extreme shape morphing, such as tendrils curling, and programmable shape morphing can be achieved. A mathematical model is established to describe how geometry and temperature affect the STS properties to optimize performance. Due to the extensibility of the STS, it can be used for a large variety of robotic applications that are partially illustrated in this research as artificial muscles, grippers, jumping robots, and soft proportional valves.
Wheeled humanoid robots have garnered significant research attention; however, their applications in close, diverse human-robot interaction remain limited due to unresolved safety and dynamic stability challenges. The human-scale body size of these robots typically results in substantial mass and elevated center of gravity, creating challenges in dynamic control and increasing fall risk during collisions. To address these challenges, this study proposes a variable stiffness mechanism (VSM) for wheeled humanoid robots that integrates vibration mitigation, falling prevention, and damping capabilities to minimize damage to both humans and robots during collisions. Comparative analysis demonstrates that robots equipped with the proposed VSM exhibit enhanced damping performance and reduced roll angles post-collision compared to conventional rigid payload-carrying wheeled mobile robots. The mechanism demonstrates superior impact force resistance, preventing falls during dynamic impact experiments. This innovation addresses critical safety concerns in wheeled humanoid robots, facilitating applications requiring close human-robot interaction.