Pneumatic and tendon‐driven actuators are widely used in soft robotic glove design. Tendon‐driven robotic gloves are generally better in controllability, dexterity, and force output, but they are less comfortable than pneumatic ones. Most soft gloves focus on only one actuation mode where either motor‐driven tendon or pump‐driven pneumatic transmission is used. Herein, a double‐acting soft actuator (DASA) that provides both tendon‐driven flexion and pneumatic extension of fingers by a single motor is presented. This is achieved by a smart pulley and bellow system. The kinematic model of the tendon‐driven flexion and the torque model of the fabric‐based pneumatic extension actuator (FPEA) are developed to analyze the DASA performance. The bending angle of the index finger actuated by the tendon and the FPEA extension torque of a joint are characterized by experimental studies. A cycle test of the DASA is conducted 3000 times, demonstrating its high repeatability. A prototype soft glove (68 g) based on the proposed DASA with a control box (835 g) is fabricated to demonstrate finger flexion and extension assistance. Based on electromyography signals, the performance of the robotic glove is evaluated by a squeezing sponge test.
Wheeled humanoid robots have garnered significant research attention; however, their applications in close, diverse human-robot interaction remain limited due to unresolved safety and dynamic stability challenges. The human-scale body size of these robots typically results in substantial mass and elevated center of gravity, creating challenges in dynamic control and increasing fall risk during collisions. To address these challenges, this study proposes a variable stiffness mechanism (VSM) for wheeled humanoid robots that integrates vibration mitigation, falling prevention, and damping capabilities to minimize damage to both humans and robots during collisions. Comparative analysis demonstrates that robots equipped with the proposed VSM exhibit enhanced damping performance and reduced roll angles post-collision compared to conventional rigid payload-carrying wheeled mobile robots. The mechanism demonstrates superior impact force resistance, preventing falls during dynamic impact experiments. This innovation addresses critical safety concerns in wheeled humanoid robots, facilitating applications requiring close human-robot interaction.
Mammal-inspired quadruped robots excel in traversing diverse terrestrial terrains but often lack aquatic mobility, limiting their effectiveness in amphibious environments. To address this challenge, an amphibious robotic dog (ARD) was developed, integrating efficient paddling gait in water with trotting capabilities on land. A canine-inspired paddling trajectory was first developed for a two-segment leg, and validated through theoretical modeling and experimental measurements of hydrodynamic forces. A waterproof ARD was then fabricated, with careful consideration of center-of-gravity and center-of-buoyancy relationships to ensure stable aquatic movement. Three distinct paddling gaits were developed and tested to evaluate the ARD’s swimming speed and stability: two lateral sequence paddling gaits (LSPG) featuring 25% and 33% power phases (PP), and one trot-like paddling gait (TLPG) featuring a 50% PP. Theoretical modeling and numerical calculations were conducted to analyze the stability of different paddling gaits. Static water experiments measured gait-specific hydrodynamic forces, followed by dynamic swimming tests demonstrating that LSPG delivers superior propulsion and speed, while TLPG offers enhanced stability. The ARD achieved a maximum water speed of 0.16 m s−1 (0.54 BL s−1) and a land speed of 0.35 m s−1 (1.2 BL s−1). These findings provide theoretical and practical guidance for the development of mammal-inspired amphibious quadruped robots, particularly in structural design and paddling gait planning.
Soft pneumatic actuators (SPAs) are widely used in robotic applications due to their inherent compliance and outstanding mechanical performance. However, a tradeoff between load capacity and deformation capacity is required when selecting material hardness for SPAs. Too hard material usually results in limited deformation, such as small extension, bending, and twisting, while too soft a material decreases robustness. This study introduces coil-reinforced flat tube actuators (CFTAs) that exhibit excellent flexibility and high load capacity by braiding flat tubes in coil springs. By adjusting the braiding pattern of the flat tube, the CFTAs can realize extending, in-plane bending, and out-of-plane helical bending motions. In addition, analytical models are proposed to predict the deformation behavior of the CFTAs and verified by experiments. The bending type CFTA deforms with an excellent curvature (0.516 mm−1) under 160 kPa input pressure, five times larger than the reported SPAs on the same scale. The CFTAs show high design flexibility by programming the flat tube pattern and using multiple coiled springs for wide application scenarios. Based on the CFTAs, this study shows wearable upper limb robots, a soft entanglement gripper, and a rob-climbing robot. CFTAs provide design insight for applications requiring dexterous and versatile deformations.
23 September 2025 in Advanced Materials Technologies