Buissiness Area Networks, Technology & Strategy, Standardts & Technology, Radio & Antennas, Radio Antennas & Algorithms, Ericsson, 16480 Stockholm, Sweden
Auto-generated profile, based on publicly available information
Christos I. Kolitsidas
Buissiness Area Networks, Technology & Strategy, Standardts & Technology, Radio & Antennas, Radio Antennas & Algorithms, Ericsson, 16480 Stockholm, Sweden
A dual-band rectenna for radio frequency (RF) energy harvesting is presented in this letter. The proposed antenna has two concentric square patches electrically connected with a small microstrip line connection. Four ports are located in the inner patch. The configuration of the ports enables a differential field sampling scheme and dual polarization. The antenna operates for the WiFi frequency bands of 2.4 GHz and 5.5 GHz with 7.52 dBi and 7.26 dBi gain respectively for each frequency. A full-wave Greinacher voltage doubler rectifier for each polarization has been employed for RF to DC conversion. The proposed novel topology utilize the differential field sampling for each polarization and quadruples the overall output voltage by the rectification process. The differential output voltage source from the rectenna can directly act as a power source as typically electronics require differential source for their operation.
8 October 2018 in IEEE Transactions on Antennas and Propagation
A wideband switched beam antenna array system operating from 2 to 5 GHz is presented. It is comprised of a 4×1 Vivaldi antenna elements and a 4×4 Butler matrix beamformer driven by a digitally controlled DP4T RF switch. The Butler matrix is implemented on a multilayer structure, using 90° hybrid couplers and 45° phase shifters. For the design of the coupler and phase shifter we propose a unified methodology applied, but not limited, to elliptically shaped geometries. The multilayer realization enables us to avoid microstrip crossing and supports wideband operation of the beamforming network. To realize the Butler matrix we introduce a step by step and stage by stage design methodology that enables accurate balance of the output weights at the antenna ports to achieve stable beamforming performance. In this work we use a Vivaldi antenna element in a linear four element array, since such element supports wideband and wide-scan angle operation. A soft condition in the form of corrugations is implemented around the periphery of the array, in order to reduce the edge effects. This technique improved the gain, the side lobes and helped to obtain back radiation suppression. Finally, impedance loading was also utilized in the two edge elements of the array to improve the active impedance. The proposed system of the Butler matrix in conjunction with the constructed array can be utilized as a common RF front end in a wideband air interface for a small cell 5G application and beyond as it is capable to simultaneously cover all the commercial bands from 2 to 5 GHz.
8 October 2018 in IEEE Antennas and Propagation Magazine
The scope of this article is to develop a modular radio-frequency (RF) energy-harvesting system for smart buildings that can act as a power source for sensing devices. Electromagnetic field-strength measurements at the main campus of the KTH Royal Institute of Technology in Stockholm, Sweden, were carried out to define the strength of the available ambient signals. Mainly two spectra were available for possible RF harvesting, i.e., two cellular bands [GSM1800 and third generation (3G)] and the 2.45-GHz Wi-Fi band. Based on these measurements, a modular approach for the system was adopted. The system is composed from two modules: 1) a Wi-Fi rectenna system composed of eight dual-polarized patch antennas and 16 rectifiers to produce eight differential voltage sources connected in series and 2) a cellular rectenna system composed of eight linear tapered slot antennas and eight rectifiers to produce four differential voltage sources connected in series. We propose an innovative multiple-input, single-output (MISO) wave rectifier that yields an efficient differential output. Both rectenna modules offer full azimuthal coverage and can operate either together or independently.
7 January 2020 in IEEE Transactions on Antennas and Propagation
A novel multiband, dual-polarized, 28-port multiple-input multiple-output (MIMO) cube is presented. The cube structure enables dense placement of the antennas, whilst still allowing for low correlation between the individual antenna ports. The total size of the cube is roughly 2 × 2 × 0.7 λ 30 , where λ 0 is the wavelength at the lowest used frequency. The novelty of the design lies in the use of a combination of orthogonally polarized endfire and broadside radiating antenna elements. Full use of all facets of the cube is achieved without the need to sacrifice bottom or top facets for mounting. Therefore, full azimuthal coverage for communication in two orthogonal polarizations is readily achieved. The system operates in both cellular and Wi-Fi bands (2.4 and 5.5 GHz), with a targeted |S 11 | below -10 dB. The MIMO performance of the system is evaluated in two environments: the rich isotropic multipath environment and the random line-of-sight environment. These two scenarios represent the edge environments of any real-life propagation scenario in terms of the directional distribution of outgoing or incoming waves at an MIMO transceiver. The intended application of the system is micro base stations and repeaters, with possible extension to massive MIMO.
Butler Matrix networks are well established as beamforming networks for phased antenna arrays. The challenge we address in this work is to cover the entire (advanced 5G or 6G) FR3 band (7–24 GHz) with a single network, while retaining low losses and minimal size. The employed multilayer topology is also well established; however, the matching between the utilized hybrid couplers and the phase shifters constitutes a major challenge for such a wideband operation. This is achieved herein by employing meander lines with appropriate curvature and introducing two distinct design methods for the Butler Matrix. The first method focuses on designing individual components separately, followed by their integration into the overall Butler Matrix structure. This approach is demonstrated through the design, prototyping, measurements, and validation of an 8 × 8 Butler Matrix beamformer, which operates across the 6–16 GHz band (FR3 Low). The second method introduces a wideband-matching technique which simplifies the implementation process by designing the Butler Matrix as a single, unified structure. This technique is applied to both 4 × 4 and 8 × 8 Butler Matrices, which are implemented and simulated for the low FR3 band. Both design methods result in wideband operation and compact size and meet the desired performance criteria.
Butler matrix networks are well established as beam forming networks for phased antenna arrays. The challenge we address in this work is to cover the entire, (advanced 5G or 6G), FR3 band (7-24 GHz) with a single network, while retaining low losses and minimal size. The employed multilayer topology is also well established, however, the matching between the utilized hybrid couplers and the phase shifters constitutes a major challenge for such a wideband operation. This is achieved herein employing meander lines with appropriate curvature and introducing two distinct design methods for the Butler Matrix. The first method focuses on designing individual components separately, followed by their integration into the overall Butler Matrix structure. This approach is demonstrated through the design, prototyping, measurements and validation of an 8x8 Butler Matrix beamformer, which operates across the 6-16 GHz band (FR3 Low). The second method introduces a wideband matching technique, which simplifies the implementation process by designing the Butler Matrix as a single, unified structure. This technique is applied to both 4x4 and 8x8 Butler Matrices, which are implemented and simulated for the low FR3 band. Both design methods result in wideband operation, compact size, and meet the desired performance criteria.