High power single-mode wafer fused 1550 nm VCSELs with an active region based on InGaAs quantum wells are fabricated. An InP-based optical cavity and two AlGaAs/GaAs distributed Bragg reflector heterostructures were grown by molecular-beam epita oy. The current and optical confinements are provided by a lateral-structured buried tunnel junction with $\sim ~6~\mu \text{m}$ diameter and etching depth of ~ 20 nm. The VCSELs demonstrate ~ 3.4 mW single-mode continuous-wave output optical power and a threshold current about 2 mA at 20°C. The output optical power exceeds 1 mW at 70°C. A −3dB modulation bandwidth > 13 GHz is obtained at 20°C. Non-return-to-zero data transmission under back-to-back condition of ~ 37 Gbps is shown.
A design of a tunnel junction (TJ) based on n++-InGaAs/p++-InGaAs/p++-InAlGaAs layers for vertical-cavity surface-emission lasers (VCSELs) for the 1.55-μm spectral range fabricated by wafer fusion of an InAlGaAsP/InP optical cavity and wafers with AlGaAs/GaAs distributed Bragg reflectors has been suggested and tested. The presence of the oxidation-resistant InGaAs layers makes it possible to employ the molecular-beam epitaxy in all stages of the fabrication technology of VCSELs, including the overgrowth of the surface profile in the TJ layer. Owing to the Burstein–Moss effect and to the thickness minimization of the p++-InGaAs layer, it was possible to avoid a buildup of the internal optical loss. As a result, the characteristics of the thus fabricated devices are comparable with those of VCSELs having an n++-/p++-InAlGaAs TJ and a similar level of the mirror losses.
The possible mechanisms of the polarization control in single-mode intracavity- contacted vertical-cavity surface-emitting lasers (IC-VCSELs) with the rhomboidal selectively- oxidized current aperture were investigated. It was found that the lasing emission polarization of all single-mode VCSELs is fixed along the minor diagonal of the rhomboidal-shape aperture (the [110] direction). Numerical modelling of carrier transport did not reveal any sufficient injection anisotropy in the laser active region, while the transverse optical confinement factors calculated for the fundamental mode with two orthogonal polarizations are identical. Optical loss anisotropy and/or gain anisotropy are the most likely mechanisms of inducing the polarization fixation.
Subject of study. This study examines vertical-cavity surface-emitting lasers (VCSELs) operating at 1.55 µm, based on strained InGaAs/InAlGaAs quantum wells. These VCSELs were fabricated using wafer-fusion (WF) technology to bond distributed Bragg reflector heterostructures with an optical cavity grown by molecular beam epitaxy (MBE). Aim of study. The aim was to assess the energy efficiency of information transmission using 1.55-µm VCSELs, fabricated using a combination of WF and MBE techniques, across a wide range of bit rates from 5 Gbits/s to 30 Gbits/s. Method. The method involved recording eye diagrams at various bit rates for VCSELs under large-signal amplitude modulation and estimating the effective modulation bandwidth and dynamic energy efficiency of the lasers via small-signal analysis. Main results. The results showed that minimum energy consumption (0.83 pJ/bit) was achieved at a bit rate of 20 Gbits/s, which is consistent with theoretical predictions. Further increasing the operating current to support higher bit rates resulted in a sharp increase in energy consumption, as the modulation bandwidth increased more slowly than did the energy input. At the maximum tested bit rate of 30 Gbits/s, where an open eye diagram was still observed, the energy efficiency decreased to 1.2 pJ/bit. Practical significance. These findings are significant for the development of energy-efficient, high-speed fiber-optic transceivers based on 1.55-µm VCSELs.