7 May 2019 in Metallurgical and Materials Transactions B
14 September 2017 in Ironmaking & Steelmaking: Processes, Products and Applications
The evolution of macro inclusions during continuous casting was investigated by large-area inclusion characterization using ASPEX and analysis of nozzle blockage deposits. Six kinds of inclusions over 5 μm were observed in samples taken from the tundish and the slabs: single alumina particles, alumina dendrites, refractory-related alumina, alumina associated with bubbles, alumina clusters and Al–Ti complex oxides. By examining the morphology of the nozzle blockage deposit, it was concluded that the refractory-related alumina in the slabs came from the decarburization layer washed away by the steel stream. Some of the alumina clusters that came from the nozzle blockage deposit dislodged by the steel flow, were formed by the agglomeration and sintering of 5–20 μm inclusions that were carried over from the tundish. Two kinds of Al–Ti oxides were found in the tundish, and their evolution mechanisms during the casting process were proposed.
3 August 2016 in Ironmaking & Steelmaking: Processes, Products and Applications
Full-scale water modelling studies combined with nail-dipping industrial trials at Shougang Jingtang (SGJT) Works were carried out in order to investigate the parameters that influence flow patterns in the continuous slab casting mould. The effects of casting speed/mould width combinations, argon bubbling flow rates, submerged entry nozzle (SEN) immersion depths and SEN geometries (port angle and bottom shape) on the flow patterns were examined. A CMI factor defined as casting speed/mould width ratio index is put forward to describe the combined effect of these parameters on the fluid flow patterns in the mould. The results show that the CMI and argon injection rates are the dominant factors that determine the flow pattern. On the basis of the results from this study, critical argon flow rates for different casting combinations have been evaluated. These findings provide operating guidelines for generating optimal flow patterns based on double roll flow with appropriate surface velocities in continuous slab casting moulds. On the basis of these considerations, slab quality at SGJT Works was substantially improved and the percentage of flow pattern-related sliver defects in cold rolled products was decreased from 4.5 to 2.3%.
8 March 2016 in Ironmaking & Steelmaking: Processes, Products and Applications
The formation and characteristics of non-metallic inclusions in 316L stainless steel produced by the AOD (argon oxygen decarburization)–ladle furnace–continuous casting process were investigated. The morphology and composition of inclusions changed significantly during the refining and casting processes. After de-oxidation with Si/Mn additions, spherical complex inclusions mainly consisting of calcium silicates were observed. The contents of MgO and Al2O3 in these inclusions continuously increased as the steel moved from the AOD through ladle processing to the tundish. As the temperature decreased from the tundish through to solidification, harmful crystals of MgO/Al2O3 spinel were precipitated within the steel melt as well as within the calcium silicate matrix of existing inclusions. The results obtained from thermodynamic calculations carried out using FactSage™ commercial software agreed well with the information derived from evaluation of the industrial samples enabling recommendations to be made for the avoidance of detrimental spinel inclusions.
31 May 2014 in International Journal of Minerals, Metallurgy and Materials
31 March 2016 in Ironmaking & Steelmaking: Processes, Products and Applications
The number, morphology, size and composition of inclusions after deoxidation and alloying in Ti-stabilised stainless steel were investigated. This was carried out by electrolytic extraction of inclusions from steel matrix, followed by microscopic examination. It was found that after the addition of ferrosilicon and manganese, and later aluminium, the composition of inclusions changed from manganese silicate-rich inclusions to alumina-rich inclusions. After tapping and titanium wire feeding, three types of TiN inclusion morphologies were observed, single, twinned and clusters. Both the turbulence and Stokes' collision mechanisms play a considerable role in the formation of TiN clusters.