Jie Luo

Jie Luo

Auto-generated profile, based on publicly available information

Jie Luo

Department of Materials Science and Engineering Monash University Clayton Victoria Australia

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2025 in Acta Materialia
Verified
Journal Article
Open access
JLJie Luo
Jie Luo
AAArtem Arlazarov
Artem Arlazarov
MPMichael Preuss
Michael Preuss
CHChristopher Hutchinson
Christopher Hutchinson

1 August 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
JLJie Luo
Jie Luo
RGRishav Ghosh
Rishav Ghosh
BSBibek Shah
Bibek Shah
ARAli Ramezannejad
Ali Ramezannejad
ASAlbert Smith
Albert Smith
MPMichael Preuss
Michael Preuss
Iron represents a cost-effective and powerful β-stabilizer that offers a potential alternative to vanadium in conventional α+β titanium alloys. However, Fe-containing titanium alloys remain relatively underexplored in part because of difficulties in their melt processing, which often leads to disadvantageous microstructures. In this study, the fast diffusion of Fe in Ti has been exploited to make model Ti-2Fe and Ti-5Fe alloys by elemental powder blending followed by hot isostatic pressing, producing homogeneous lamellar α+β microstructures with low porosity and weak crystallographic texture. Mechanical testing revealed a substantial increase in strength relative to CP-Ti, arising from Fe solid-solution strengthening of the β phase and the formation of an incommensurate ω phase. However, increasing Fe content reduced ductility and led to a pronounced decrease in fracture toughness in Ti-5Fe. EBSD and slip trace analysis has been employed in-situ during loading to elucidate the underlying deformation mechanisms. Deformation was found to be highly heterogeneous and governed by the distinct plastic responses of the α and β phases together with the effectiveness of slip transfer across α/β interfaces. Ti-2Fe exhibited more homogeneous strain accommodation, facilitated by coarse α colonies and wider α laths that promoted deformation compatibility between neighboring microstructural regions. In contrast, the high β fraction and increased interfacial constraint in Ti-5Fe intensified strain localization, promoted deformation heterogeneity, and accelerated fracture. These results demonstrate that deformation compatibility across α/β interfaces plays a central role in controlling strain localization, fracture resistance, and the strength-ductility balance, providing microstructural design guidelines for low-cost Fe-containing titanium alloys.

18 April 2026 in Advanced Engineering Materials
Verified
Journal Article
Open access
JXJiaqi Xu
Jiaqi Xu
XZXun Zhang
Xun Zhang
JDJack M. Donoghue
Jack M. Donoghue
ASAlbert D. Smith
Albert D. Smith
RURahul Unnikrishnan
Rahul Unnikrishnan
PWPhilip John Withers
Philip John Withers
Some alloys are difficult to make by ingot metallurgy. Here, the potential for making alloys by hot isostatic pressing (HIPing) and homogenising powder mixtures is explored for Ti–Fe. Iron is an effective and cost‐effective β stabiliser but gives rise to segregation issues during solidification. Exploiting the fact that Fe diffusion through Ti is fast, Fe and Ti powders are co‐HIPed at, and homogenised at, only 800°C in order to create an α+β microstructure based on small prior β grains. The evolution of phase composition and elemental distribution during homogenisation has been tracked quantitatively in 3D by X‐ray computed tomography and in 2D by energy dispersive spectroscopy and electron backscatter diffraction. The final homogenised microstructure consists of fine α Ti laths separated by β ligaments with a prior β grain size of only 80 μm, free of TiFe intermetallics with no indication of a grain boundary α constituent. Kirkendall pore formation was observed during homogenisation heat treatment due to the fast diffusion of Fe in Ti. This study shows the potential of HIP processing followed by homogenisation heat treatment as a novel solid‐state manufacturing route for difficult‐to‐cast alloys.

1 January 2025
Verified
Conference Paper
Open access
PDF file
JLJie Luo
Jie Luo
ASAlbert D. Smith
Albert D. Smith
JDJack M. Donoghue
Jack M. Donoghue
JXJiaqi Xu
Jiaqi Xu
JNJuan Nunez-Iglesias
Juan Nunez-Iglesias
MPMichael Preuss
Michael Preuss
Micro- and nanoscale in-situ investigations of engineering alloys’ behaviours during deformation [ 1- 5] and/or heating [ 6- 8] have intensified in recent years, partly driven by advances in in situ characterization tools, enabling new insights into material behavior. Here we examine the capabilities and potential of automated in-situ characterization capabilities of the newly developed Tescan and Newtec In-Situ Testing (TANIST) system. It is a specialized system for conducting thermal and mechanical tests while simultaneously capturing microstructural observations at high spatial and temporal resolutions. This system supports full automation, enabling continuous 24/7 experimentation and facilitating measurements over a broader range with finer load and temperature increments than previously achievable [ 9]. The system facilitates the capture of plasticity localization through high-resolution digital image correlation (HRDIC), which is crucial for understanding the damage and failure mechanisms in engineering alloys. Simultaneously, precise monitoring of microstructural changes, including phase transformations and chemistry distribution evolution, is possible using complementary detectors such as electron backscatter diffraction (EBSD) and energy dispersive X-ray spectroscopy (EDX). Furthermore, the concurrent development of data analysis tools, such as DefDAP [ 10], a Python library for correlating EBSD and HRDIC data, enhances the wealth of information obtainable through in-situ testing. This talk will start by presenting an introduction to the TANIST system, developed by Tescan and NewTec in collaboration with the Henry Royce Institute. The first system in Australia is now available at Monash University within the Monash Centre for Electron Microscopy (MCEM). Several case in situ studies will be presented, including in-situ loading studies utilizing EBSD and HRDIC on a TRIP-assisted advanced high strength steel, in-situ loading investigations employing EBSD and in-situ heating observations using EDX and EBSD on hot isostatic pressed (HIPped) Ti-Fe alloys.