1 December 2014 in Journal of Materials Processing Technology
25 April 2018 in Journal of Engineering for Gas Turbines and Power
In noncontact annular labyrinth seals used in turbomachinery, fluid prerotation in the direction of shaft rotation effectively increases fluid velocity in the circumferential direction and generates fluid forces with potential destabilizing effects to be exerted on the rotor. Swirl brakes are typically employed to reduce the fluid prerotation at the inlet of the seal. The inlet flow separates as it follows the swirl brakes, and the ratio between tangential component of the velocity at the seal, and the velocity of the rotor surface varies consequently. Effective swirl brakes can significantly suppress the destabilizing fluid forces as it is effectively reducing the tangential velocity. The literature shows that leakage rate can also be reduced by using swirl brakes with “negative-swirl.” In this study, a labyrinth seal with inlet swirl brakes is selected from the literature and considered the baseline design. The seal performance is evaluated using ANSYS-cfx. The design of experiments (DOEs) approach is used to investigate the effects of various design variables on the seal performance. The design space consists of the swirl brake's length, width, curvature at the ends, the tilt angle, as well as the number of swirl brakes in the circumferential direction. Simple random sampling method with Euclidean distances for the design matrix is used to generate the design points. Steady-state computational fluid dynamics simulations are then performed for each design point to analyze the performance of the swirl brakes. Quadratic polynomial fitting is used to evaluate the sensitivity of the average circumferential velocity with respect to the design variables, which gives a qualitative estimation for the performance of the swirl brakes. These results assist in creating a better understanding of which design variables are critical and more effective in reduction of the destabilizing forces acting on the rotor, and thus will support the swirl brake design for annular pressure seals.
11 April 2017 in Journal of Engineering for Gas Turbines and Power
Textured thrust bearings are capable of providing higher load capacity and lower friction torque compared to nontextured bearings. However, most previous optimization efforts for texturing geometry were focused on rectangular dimples and employed Reynolds equation. Limited studies have been done to investigate the effects of partially textured thrust bearings with elliptical dimples. This study proposes a new optimization approach to find the optimal partially texture geometry with elliptical dimples, which maximize the loading capacity and minimize the friction torque. In this study, a 3D computational fluid dynamics (CFD) model for a parallel sector-pad thrust bearing is built using ANSYS cfx. Mass conserving cavitation model is used to simulate the cavitation regions. Energy equation for Newtonian flow is also solved. The results of the model are validated by the experimental data from the literature. Based on this model, the flow pattern and pressure distribution inside the dimples are analyzed. The geometry of elliptical dimple is parameterized and analyzed using design of experiments (DOE). The selected geometry parameters include the length of major and minor axes, dimple depth, radial and circumferential space between two dimples, and the radial and circumferential extend. A multi-objective optimization scheme is used to find the optimal texture structure with the load force and friction torque set as objective functions. The results show that the shape of dimples has a crucial effect on the performance of the textured thrust bearings. Searching the design space for a proper combination among the design variables satisfying the constraints has the advantage of capturing the codependence among design variables and leads to a surface patterning of the bearing, which showed a 42.7% improvement on the load capacity.
20 April 2017 in Journal of Fluids Engineering
Hybrid bearings are mostly used in high-speed and load situations due to their better stability and loading capacity. They are typically designed with recess grooves to enhance both static and dynamic performance of the bearing. Previous theoretical studies on the influence of the recess geometrical shapes often utilize the Reynolds equation method. The aim of this paper is to analytically study the influence of various recess geometrical shapes on hybrid journal bearings. A three-dimensional (3D) computational fluid dynamics (CFD) model of a hybrid journal bearing is built, and a new method of response surface model is employed to determine the equilibrium position of the rotor. Based on the response surface model, an optimization scheme is used to search around the equilibrium position to get an accurate solution. The current analysis includes the geometries of rectangular, circular, triangular, elliptical, and annular shaped recesses. All these different shapes are studied assuming the same operating conditions, and static properties are used as the indices of the bearing performance. This study proposes a new design process using a CFD method with the ability of calculating the equilibrium position. The flow rate, fluid film thickness, and recess flow pattern are analyzed for various recess shapes. The CFD model is validated by published experimental data. The results show that the response surface model method is fast and robust in determining the rotor equilibrium position, even though a 3D-CFD model is utilized. The results suggest that recess shape is a dominant factor in hybrid bearing design.
13 June 2018 in Journal of Tribology
Contact performance can be enhanced by using textured surfaces. These are also found to have influences on lubricated contacts. A procedure to find the optimal partially textured thrust bearing configuration is presented in this study. A parallel sector-pad thrust bearing is simulated by a three-dimensional (3D) computational fluid dynamics (CFD) model. The stationary surface of the bearing is textured with dimples, while the rotor surface is flat. The results of the baseline model are validated by experimental data. In this study, we compare rectangular and elliptical dimples by investigating design parameters, such as major the length of the major axis (width), the length of the minor axis (length), dimple depth, circumferential space between two dimples, radial space between two dimples, radial extent, circumferential extent are selected as design parameters. A parametric study is conducted to investigate the influence of the texture geometries and a surrogate model is created. Based on the surrogate model, a multi-objective optimization scheme is used to navigate the design space and find the optimal texture structure that provides a lower maximal temperature inside the fluid film, higher load capacity, and lower friction torque. The results show that the optimal radial extent of the texture is around 80% of the pad radial length for both cases. The optimal length of the elliptical dimples in the circumferential direction is about 30% larger than the value of the rectangular dimples. In the final optimal design, the maximal temperature reduces 1.1% and 1.3% for rectangular and elliptical dimples while the load capacities are maintained at the same level.
21 June 2017 in Journal of Engineering for Gas Turbines and Power
Hybrid bearings are getting more and more attention because of their ability to provide both hydrodynamic support for high-speed rotors and hydrostatic lift in low-speed conditions such as during startup. Hybrid bearings are typically designed with recess grooves to modify the pressure profile and as a result to enable the lift capacity of the bearing under various operating conditions. The literature has shown that the size and shape of the recesses have not been systematically and quantitatively studied in detail. The goal of this study is to build a 3D analytical model for a hybrid-recessed bearing with five pockets and provide a comprehensive analysis for the effect of recess geometry on the overall performance of the bearing. In this study, a baseline model selected from the literature is constructed and validated using the ANSYS cfx computational fluid dynamics software package. A sensitivity analysis of the design variables on the performance of the bearing has been performed using design expert software. The length, width, and depth of the recess as well as the diameter and location of the five inlet ports have been selected as design variables. A multivariable and multi-objective genetic algorithm has also been solved using isight software with the goal of optimizing the geometry of the recess to maximize load capacity while minimizing bearing power loss from friction torque. The results of the baseline model show reasonable agreement with the experimental data published in the literature. The regression models for lift force and friction torque were both found to be statistically significant and accurate. It has been shown that friction torque decreases as the length of recess in the circumferential direction increases. The results showed that the load capacity is highly correlated to the diameter of the orifice, d. These results provide a deeper understanding of the relationship between the shape of the recess and bearing performance and are expected to be useful in practical hybrid-bearing design.