1 January 2019 in Advances in Civil Engineering
In order to study the diffusion law of grouting slurry in sand areas, the grouting of cement slurry in sand was analyzed by the indoor grouting test under different water‐cement ratios, grouting pressures, grouting amounts, and soil qualities, and the law of the post‐grouting slurry is obtained. The results show that the grouting method is affected by the grouting pressure, water‐cement ratio, grouting amount, and soil quality. Under the same grouting pressure, the diffusion modes of different water‐cement ratio grouts in sands with different permeability coefficients, which are mainly manifested as osmotic diffusion, are basically the same; under the same water‐cement ratio, when the grouting pressure is relatively small, the diffusion of modes of slurry is mainly osmotic in sand. The diffusion radius of cement slurry in sand has a good power function relationship with grouting pressure, water‐cement ratio, permeability coefficient, and grouting amount. And, the empirical function model of slurry diffusion radius is proposed by regression analysis. The research results provide a certain theoretical and experimental reference for post‐grouting in sandy areas.
1 January 2018 in Advances in Civil Engineering
The surface morphology of a discontinuous structural plane in a natural rock mass is irregular. In studies on the shear strength of discontinuous structural planes, Barton introduced the joint roughness coefficient (JRC) to describe and calibrate the morphological characteristics of a rough structural plane. To describe Barton’s typical rough profile model, researchers commonly conduct a comparison based on a standard curve. This approach does not guarantee graphic precision. With subjective comparison reference drawing, the size and angle of a structural plane cannot be quantitatively controlled, and small bumps cannot be described. When the influence of the roughness coefficient of a rock surface is discussed, errors are caused by comparing Barton’s typical roughness profile model and a general structural surface model. This paper proposed a new method to simulate Barton’s typical structural surface. A numerical model of a complex structural plane is built automatically. The effects of cohesion and internal friction angle on the shear strength of the structural plane are discussed by changing the value of the shear strength parameters.
20 February 2009 in Microchimica Acta
22 March 2022 in Geofluids
Under the condition of constant external stress, the displacement and stress of the joint will be adjusted continuously with time, resulting in the creep phenomenon, that is, the continuous increase of the strain with time, which further causes the damage of the jointed rock mass. In order to study the size effect of joint shear rheological mechanical properties, this paper conducted shear rheological numerical simulations on nonpenetrating and penetrating joint models established in Particle Flow Code (PFC) and analyzed the effect of specimen size on the rheological and shear mechanical behavior of the model. The results show the following: (1) For the rheological direct shear test, the instantaneous shear displacement of the joint increases continuously as the size increases, showing a significant positive size effect. (2) For through-type joints, only the cohesion shows a certain size effect, and the shear strength and friction angle have a nonobvious relation with specimen size. (3) For anchored through-type joints, the increase of the model size leads to a decrease in shear strength, while the friction angle-size effect of joints is not remarkable.
1 January 2018 in Advances in Civil Engineering
The performance of asphalt pavement is determined by the combination of its material properties, road structure, and loading configurations. A DEM numerical simulation study was conducted to determine stress distribution and deformation behavior of asphalt pavement with graded aggregate base under standard traffic loading. Stress contour and displacement contour were presented via a self‐made program. Compressive stress concentrated area located in both sides of wheel, while tensile stress concentrated area appeared in lower part of the asphalt layer. The traffic loading transferred downward by graded aggregate base and to both sides at the same time, and has a trend to expand gradually with increasing depth within graded aggregate base. Therefore, stress was well distributed in the subgrade soil layer with a great action scope, and the value decreased obviously because of the stress dispersion of graded aggregate base. Vertical displacement was the main displacement of the asphalt layer, and on the both sides of traffic loading, displacement was downward and inclined slightly to the central of loading. Vertical and horizontal deformations included in both graded aggregate base layers, and displacement extended to both sides gradually with increasing depth corresponding to stress‐distribution trends. Vertical displacement was dominated in the subgrade soil layer which was relatively small.