9 October 2024 in IEEE Transactions on Power Electronics
A new high-power two-port multiple-frequency LLLC induction heating power system is proposed in this article, which can simultaneously achieve multiple-frequency, multiple-power, and high-efficiency output. A two-port LLLC resonant tank with an inverter at each port is used to power the load. The multiplication of output power and frequency is achieved by coordinating the operating modes of the two inverters. In order to improve the efficiency of the system, a design methodology for tank parameters is proposed, ensuring that the system operates at the optimum point of efficiency, thereby avoiding reactive power losses and realizing zero voltage switching (ZVS). Additionally, an adjusted-pulse density modulation (PDM) (APDM) control method is proposed, which can further enhance the efficiency of PDM control. The shortcomings, such as large current fluctuation and the tendency to lose lock, are optimized, allowing the system to operate with high efficiency across the full power range. Finally, an experimental prototype (SiC mosfet ) is developed to verify the feasibility of the topology, parameter design methodology, and APDM.
27 November 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Given the high power requirements of commercial automatic cooking machines, a comprehensive all-metal induction heating power system with an energy storage port is proposed. The energy storage port serves to peak-shave the Induction Heating (IH) system and utilizes time-of-use electricity pricing to save costs. While domestic induction heating is primarily used for ferromagnetic (FM) pots, there is a challenge with non-ferromagnetic (NFM) pots due to their small equivalent resistance, which can easily cause overcurrent issues of inverter. To achieve all-metal heating, a dual-resonance topology inverter with switches is proposed. The system can utilize a half-bridge LC series resonant inverter for heating FM pots or a full-bridge LLLC resonant inverter for heating NFM pots. Compared to the LLC resonant circuit, the LLLC resonant circuit significantly reduces output impedance angle and switching losses, thereby improving system efficiency. Additionally, an APDM-PFM control strategy is proposed for heating NFM cookware. During heavy loads, an Average Pulse Density Modulation (APDM) control strategy is adopted for power regulation; while during light loads, the system switches from full-bridge (FB) resonant inverter to half-bridge (HB) resonant inverter, and the control strategy changes from APDM to Pulse Frequency Modulation (PFM). This ensures that the load current remains continuous, allowing the system to operate efficiently across the entire power range. Finally, a 5.5kW/10kHz experimental prototype was developed. The topology, the parameter design method and the control strategy were verified through this prototype.
11 June 2025 in IEEE Transactions on Power Electronics
The full-range zero voltage switching (ZVS) comprehensive control strategy is proposed for a high-power dual-port LLLC induction heating system which allows the system to operate efficiently across the entire power range. Under heavy load, a novel dual-phase-shift (DPS) control strategy is proposed in this article. Using time-domain analysis, the minimum circulating current curve and the ZVS range under DPS conditions are derived. The optimal phase-shift angle relationship is determined by combining the minimum circulating current and the full-range ZVS region. However, under DPS control, the minimum output power is one-quarter of its full load capacity due to the lack of internal phase-shift in inverter II. To overcome this limitation, a frequency-doubling pulse frequency modulation (FD-PFM) control strategy is proposed under light load. Frequency-doubling control is implemented through time-division multiplexing between the two inverters, which enables the resonance circuit frequency to be doubled without altering the switching frequency of each inverter. The FD-PFM approach facilitates a faster response to power variation with frequency, enabling the system to adjust power in a narrower frequency range. This enables smooth, wide-range power adjustment across the entire system and ensures ZVS operation across the full power range. A 14 kW prototype was developed, and the experimental results align closely with the theoretical analysis.
4 November 2025 in IEEE Transactions on Industrial Electronics
Pulse density modulation (PDM) is commonly used in induction heating (IH) to enhance inverter efficiency. However, PDM can cause significant fluctuations in the output current, especially under light-load conditions, leading to current intermittency and thereby causing the phase-locked loop to lose lock. Due to the limited output levels of the full-bridge inverters, the PDM improvement schemes applicable to LLC resonant tanks are constrained. To address this issue, an IH topology based on a T-type resonant inverter is proposed in this article. By coordinating the operation of each leg, this topology extends the output levels of the inverter while ensuring soft switching for all power devices. Aiming at the problems of PDM, a hybrid PDM (HPDM) is introduced, which can optimize the pulse sequence distribution and level configuration, effectively reduce current fluctuation amplitude and mitigate current intermittency. Moreover, a reconfigurable LLC-L resonant tank is proposed, utilizing dynamic impedance adjustment to promote more uniform pulse sequence distribution, and further alleviating current fluctuations. The experimental results validate the effectiveness of the proposed method. Compared with PDM, HPDM reduces current ripple by more than half and also improves system efficiency.
1 July 2026 in IEEE Transactions on Industrial Electronics
6 March 2026 in IEEE Transactions on Industrial Electronics
Pulse density modulation (PDM) can reduce switching losses by achieving zero voltage switching (ZVS) and zero current switching (ZCS), enabling high-efficiency operation of resonant converters. However, the pulse density in PDM is defined as the ratio of the number of minimum energy transfer cycles to the total number of control cycle N. This fixed minimum energy unit restricts the ability to continuously regulate the input current and, due to the discrete nature of the PDM, often requires a large value of N to achieve regulation, thereby increasing resonant voltage ripple. To address these limitations, a continuously enhanced pulse density modulation (CEPDM) strategy is proposed, which integrates half-cycle enhanced pulse density modulation (EPDM) with phase shift modulation (PSM) by embedding PSM within the passive mode of half-cycle EPDM. This strategy enables continuous current regulation within a fixed and limited total control cycle N, thereby decreasing voltage ripple. Furthermore, a fourth-order CLCL resonant circuit is proposed to solve the DC offset issue associated with half-cycle EPDM in a third-order CLC resonant circuit.