Evren Ozbayoglu

Evren Ozbayoglu

Auto-generated profile, based on publicly available information

Evren Ozbayoglu

The University of Tulsa Drilling Research Projects

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2018 in Journal of Petroleum Science and Engineering
Verified
Journal Article
Closed access
SBSilvio Baldino
Silvio Baldino
ROReza E. Osgouei
Reza E. Osgouei
EOEvren Ozbayoglu
Evren Ozbayoglu
SMStefan Z. Miska
Stefan Z. Miska
RMRoland May
Roland May

8 June 2014
Verified
Conference Paper
Closed access
PDF file
YCYuanhang Chen
Yuanhang Chen
MYMengjiao Yu
Mengjiao Yu
SMStefan Miska
Stefan Miska
EOEvren Ozbayoglu
Evren Ozbayoglu
YKYongfeng Kang
Yongfeng Kang
NANasser Al-Khanferi
Nasser Al-Khanferi
Lost circulation is one of the most persistent and costly drilling problems that drilling engineers have been struggling with for decades. The main reason why some of the remedial procedures are not working as planned is the lack of information, such as the location of the loss zone. The pinpointing of the zone of loss will allow the treatment to be applied directly to the point of loss rather than to the entire open hole. This paper presents an approach to predict the location of loss zone from the transient mud circulation temperature profile altered by the mud loss. A numerical model in estimating the transient mud circulating temperature profile during a lost circulation event is developed. The temperature profile in both the flow conduits (drillpipe and annulus) are modeled using mass and energy balance. The flow rate of drilling mud decreases in the annulus above the loss zone as part of the fluids lost into the fractures, which in turn alters the heat transfer between the drillpipe, annulus, and formation. The wellbore is divided into two multiple sections, which account for single multiple loss circulation zones. Rigorous heat transfer in the formation is included. Case studies are performed and numerical solution results are presented and analyzed. According to the results, temperature alterations induced by mud loss include: 1) Declines in both bottom-hole temperature (BHT) and mud return temperature over time, and 2) Discontinuity in the first order derivative of annulus temperature with respect to depth at the location of loss zone; meanwhile, the temperature alterations are mainly controlled by the mud loss rate and location of loss. By matching the simulated results with the distributed temperature measurements at different times, the depth of the loss zone can be identified. This piece of information is important for the spotting of LCM (lost circulation material) pills, the optimization of overbalance squeezing pressure, as well as the consideration of setting the cement plug or additional casing.

23 May 2025 in SPE Journal
Verified
Journal Article
Closed access
HPHarsh Patel
Harsh Patel
SBSilvio Baldino
Silvio Baldino
EOEvren Mehmet Ozbayoglu
Evren Mehmet Ozbayoglu
Summary: Severe casing wear during the drilling of complex, tortuous, and highly deviated well trajectories is a pressing issue, leading to casing wall thickness reduction and consequent tubular degrading. Addressing this problem requires experimental studies on controllable parameters in combination with theoretical tribology analysis. In this work, we investigate the key factors that affect casing wear, describe a closed-loop testing approach, introduce an alternative geometrical model for quantifying wear volume, and provide a more detailed prediction of contact-time-dependent wear depth supported by more granular casing wear factors. Our results show that a contact-time-dependent wear factor should be accounted for as one of the controlling parameters for nonlinear wear penetration. We further investigate the impact of fluid flow regimes on wear profiles under three-body abrasion (inclusive of cuttings), which is critical and has remained a relatively underexplored area. In addition, our work addresses the long-standing discussion on whether wear is more pronounced in water- or oil-based systems, drawing a direct comparison between the two. Finally, it was observed that wear is not uniformly distributed under three-body abrasion; depending on where cuttings accumulate (entry side), wear depth is significantly larger compared with the exit side of the annulus between the tool joint and casing, highlighting the need for a deeper understanding of localized wear mechanisms. The work undertaken in this project offers a closer look into wear factor selections and a framework that could help improve predictions and hence mitigate casing wear.

1 January 2022 in SSRN Electronic Journal
Verified
Preprint
Open access
PDF file
YLYaxin Liu
Yaxin Liu
EOEvren M. Ozbayoglu
Evren M. Ozbayoglu
EUEric R. Upchurch
Eric R. Upchurch
SBSilvio Baldino
Silvio Baldino
Motivated by a dearth of research on the dynamics of single Taylor bubbles in annular conduits, a computational study of Taylor bubbles rising in vertical and inclined annuli is performed using a three-dimensional (3D) computational fluid dynamics (CFD) simulation with the Volume-of-Fluid (VOF) method implemented in the commercial software ANSYS Fluent (Release 19.2). The effects of Eötvös number (Eo = [10, 300]), inverse viscosity number (Nf = [40, 320]), and inclination angles (θ = {10°, 20°, 30°,…, 80°}) on the steady-state Taylor bubble shape and rise velocity are investigated. The latter is parameterized by Froude number (Fr) and simulations are carried out keeping constant liquid-gas density ratio and dynamic viscosity ratio at 1000 and 100, respectively. The simulation results provide good agreement with the existing numerical findings and experimental observations. For Taylor bubbles in a vertical annulus, the surface tension and liquid viscosity show significant impacts on bubble shape (length and trailing edge) and Fr for Eo = [10, 100] and Nf = [40, 160]. A correlation for Fr in terms of Eo and Nf is proposed and compared against 66 numerical simulations and 20 air-water experimental results available in the literature, resulting in average errors of 2.13% and 5.52%, respectively. Relatively large errors of 7.38% for characteristic dimension D* ≤ 45 mm and 11.82% for D* ≥ 344.9 mm are observed (D* = Do + Di). The correlation exhibits improved performance with an average error of 3.5% for 45 mm ≤ D* ≤ 214 mm relative to the only existing model. The shape of bubbles and Fr values in inclined annulus, where the bubble becomes more streamlined and unfolded, are observed to be dramatically different from those in vertical annulus. Interestingly, the wrap angle (θwrap) decreases linearly with the increase of inclination angle. Predictions of the dimensionless rise velocity in inclined annulus are made and successfully compared with an existing model and experimental data from the literature.