1 January 2020 in IEEE Transactions on Industrial Electronics
In grid-connected solar PV, the size and cost become higher due to the presence of a transformer. This transformer deteriorates the entire solar PV system efficiency. To overcome this limitation, a switched capacitor-inductor network (SCLN) based ultra-voltage gain dc-dc converter using a single switch is presented in this paper. The SCLN converter can achieve ultra dc-voltage gain with minimum number of devices when compared to other existing converters. Moreover, the voltage gain is significantly improved at entire duty ratios. In addition, due to switched approach of inductor and capacitor, the converter provides lesser ripple content in the output voltage and current. The operation of the converter in CCM and DCM are discussed. The parasitic elements are considered to estimate the dc-voltage gain and the efficiency of the converter more precisely. The small-signal model of the converter is derived, and the pole-zero locations are investigated. Moreover, the comparative performances of SCLN converter with existing converters are reported. A hardware prototype has been developed and tested. To prove the applications of the SCLN converter in solar PV system, the experimental results are observed by considering the output voltages of i) 650 V for three-phase and ii) 325 V for single-phase applications.
10 January 2019 in IEEE Transactions on Circuits and Systems II: Express Briefs
2 May 2019 in IEEE Transactions on Industry Applications
The implementation of a non-isolated dual input bridge type DC-DC converter for hybrid energy source integration is discussed in this paper. The proposed converter accommodates two sources using an inductor, a capacitor, two IGBTs without the anti-parallel diode and two IGBTs with the anti-parallel diode. The different modes of operation of the converter are explained with detailed analytical waveforms and equivalent circuits. From the analysis, the steady state output equation of the converter is derived. The boundary condition between the CCM and DCM operations is also derived. The dynamics of the converter is analyzed in detail with help of a small signal model. The step response of different transfer functions is discussed. The computer simulations of the proposed converter topology have been carried out using MATLAB/Simulink?. An experimental prototype of the proposed converter is also built and tested successfully in the laboratory environment. Performance comparison of the proposed converter is carried out with the conventional converter topologies in terms of component counts, efficiency, loss breakdown, and power density.
11 July 2019 in IET Power Electronics
The electric vehicle (EV) is becoming a more attractive solution to avoid fossil fuel usages in India. In the commercial EV, the solar PV charges the battery and simultaneously the battery drives the vehicle. Due to the structure of conventional buck‐boost bidirectional DC–DC converter, the solar PV power becomes underutilised when the battery state of charge (SOC) reaches its optimal value. In order to overcome this limitation, this study proposes a novel dual input superboost (DISB) DC–DC converter for solar‐powered EVs. The proposed converter effectively utilises the solar PV power by operating in six different modes. Also, it has the advantages of wide range of speed control and reduces the number of conduction devices in each mode, thereby enhancing the efficiency. This study presents detailed operating waveforms and dynamic analysis of the proposed DISB DC–DC converter. Furthermore, the operation and performance of proposed converter under six different modes are validated through simulation and confirmed with an experimental investigation.
7 September 2020 in IEEE Transactions on Circuits and Systems II: Express Briefs
A multi-stage ultra-gain converter using minimum component including a single semiconductor switch is proposed. The proposed converter is formulated using an active inductor-capacitor-two diodes (LC2D) network. The basic structure of the converter called as a cubic gain converter is formulated using twelve components including a semiconductor switch. The operation of the converter is discussed for continuous and discontinuous modes of operations. The converter performance due to the parasitic elements is discussed, and the SiC-based semiconductor devices are selected to reduce the effect of parasitic elements. A 250 W, 50 kHz cubic gain converter prototype is made and the test results are recorded. The results prove that the operation of the cubic gain converter in low duty ratio helps to attain 91.6% efficiency. The proposed structure of the n-stage and the detailed analysis of the cubic gain converter are the major novelties and contributions of this paper.
7 December 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Electric Vehicles (EVs) become a more prominent solution to replace all fossil fuel-based combustion vehicles. During the parking of EVs, power produced by solar photovoltaic (PV) present in the PV powered EVs is underutilized when the capacity of the EV battery is full. Also, a converter is devoted in the conventional EVs to perform the vehicle to grid (V2G) or vehicle to vehicle (V2V) operation. To utilize PV and to perform V2G operation, a novel non-isolated dual-input single output DC-DC converter (DISOC) is proposed. The DISOC structure can be reconfigured to perform six types of operation based on the status of power availability with PV, battery and also the running status of the EV. Simultaneous power transfer from both the input sources, charging the battery from solar PV, V2G and G2V operations are the key features of the proposed converter. The converter operation, component design, effect of parasitic elements on the converter performance, small-signal model, etc., have been reported. The hardware prototype of the converter is fabricated for 500 W, and the experimental results are presented.