This article proposes an adaptive sliding-mode control (ASMC) with a modified reduced-order proportional integral observer (MROPIO) to provide speed control for a permanent magnet synchronous motor against unknown disturbances, such as system parameter uncertainties and external load torque variation. The ASMC method, based on a new sliding-mode reaching law, improves chattering in the control signal and reduces the time required for the system trajectory to reach the sliding-mode surface. The MROPIO estimates unknown disturbances and provides feed-forward compensation for the ASMC, thus overcoming incorrect estimations of unknown disturbances during speed jumps can cause overshoots in the speed response. All the proposed methods were implemented on an industrial motor drive. The experimental results confirm the validity of the proposed method for practical applications.
12 June 2020 in IEEE Transactions on Industrial Electronics
This article proposes a method to improve the accuracy of a vernier absolute magnetic encoder. The encoder consists of a master and a nonius multipolar magnetic track. Sinusoidal signals from the master and nonius tracks are used to infer the absolute information. Unfortunately, these signals are contaminated by nonideal factors such as different amplitudes, dc-offsets, phase shifts, and random noise. Moreover, harmonics existing in the encoder signals distort the vernier principle and significantly affect the accuracy of the encoder. To address these problems, the present article proposes an efficient method with three main parts. The first is an observer phase-locked loop (OPLL), which is used to estimate the phase and eliminate the nonideal factors. The second is nonlinear phase compensation, which is used to correct the vernier principle that deviated due to the existing harmonics. Finally, a pole pitch compensation method is introduced to modulate the master phase angle from the OPLL to eliminate the harmonic distortion. The proposed method can eliminate the nonideal factors, harmonic distortion and improve the accuracy of the encoder. All the proposed methods were implemented on an ARM STM32F407ZG. The experimental results confirm the validity of the proposed method for practical applications.
This paper combines the extended Kalman filter (EKF), dual quantum-behaved particle swarm optimization (DQPSO), and adaptive neuro-fuzzy inference system (ANFIS) to propose a novel robot calibration method. Robot precision is influenced by kinematic and non-kinematic error sources. The EKF algorithm is robust for the nonlinear system with Gaussian noise to identify kinematic parameter errors for kinematic calibration. However, if inappropriate covariance matrices are selected, the EKF algorithm may converge to an incorrect solution. To increase the effectiveness of the EKF algorithm, we propose a DQPSO algorithm that consists of the QPSO-1 and QPSO-2 algorithms. The QPSO-1 algorithm adapts the covariance matrices of measurement noise and process noise, while the QPSO-2 algorithm optimizes the kinematic parameter errors estimated by the EKF algorithm. In addition, the used ANFIS predicts and compensates the non-kinematic error for non-kinematic calibration. Experiments have been performed on a five-bar parallel robot to confirm the effectiveness of the proposed method. The experimental results demonstrate that the proposed method significantly improves the positional accuracy, and is better than the previous methods.
A network-based control system includes many connected devices, and time synchronization plays an important role in the unified operation of those systems. A clock servo needs a guarantee time offset and a clock rate to minimize the time difference between devices. This paper proposes an adaptive clock servo to improve time synchronization. This proposed algorithm uses a fuzzy-based proportional-integral clock servo (fuzzy-PI) based on IEEE 1588 to reduce the frequency of clock compensation. This method adapts the bandwidth and enhances noise reduction, improving both the time offset and rate difference between the slave and master. The node time can synchronize with the master time after just one cycle of synchronization. Experiments validated the effectiveness of the algorithm and demonstrated that the slave can track the master with the mean and standard deviation of the time offset are 0.432ns and 4.402ns. A cycle time of one second is used to ensure a low-bandwidth network. With these results, the number of nodes over a real-time network can be increased.
In Network Control Systems (NCSs), a dual rate controller is an approach that is applied to reduce the influence of packages loss and random delays. If the output measuring sensors is slower than the control action update can be reached, the dual rate controller is used as a possible solution. In this paper, a fuzzy controller will be combined with a dual rate controller in an NCS to regulate the gain parameter online. The fuzzy dual rate PID is designed by slitting a convention PID into two parts performing at different sampling rate. A Controller Area Network (CAN) is the mode of communication in this system. Furthermore, the Fuzzy-dual rate PID controllers performance is compared with that of a conventional PID controller. Based on the simulation results and experimental results, the fuzzy dual rate PID controller provides a superior position response with a faster rise time, faster settling time and it minimizes the amount of overshoot.
Real-time is a challenge facing the industrial communications technology. For this purpose, a large number of protocols have been promoted to enable the goal of real-time control. In the first time, many network types are developed based on CAN. In this time, Ethernet is a trend in modern industrial network. A chosen the best one plays an importance role in engineering. In this paper, the authors present an evaluation on the performance of two networking protocols: Mechatrolink III and SSCNET III. In each network type, the commonly theories are presented. We also consider how each protocol be used on the networked control system. Moreover, each protocol is developed on STM32F207 to evaluate the time communication individually. The cycle time is measured to demonstrate the performance of each network type.