In order to understand the impact resistance of shear thickened gel (STG) and find a simple test method for impact resistance, the composite fabric of shear thickened gel and warp knitted spacer fabric was prepared by impregnation and filling, and its performance was evaluated by bursting strength test and drop hammer impact test. The outcomes showed that the bursting strength, bursting elongation and bursting work of the samples prepared by impregnation method increased with the increase of shear thickening gel ratio, and the samples prepared by ethanol and gel dilution with the mass of 1:9 had the best performance. The two groups of composite materials prepared by immersion method and filling method showed an increase of 51% in energy absorption compared to the original sample in the drop hammer impact test 85% and 76 54%. The impact resistance of warp knitted spacer fabric with shear thickening gel is greatly improved. The use of the top burst test method can replace the drop hammer impact test for evaluating the impact resistance of fabrics.
27 October 2026 in European Journal of Applied Science, Engineering and Technology
Laser-assisted ultrasonic surface rolling (LA-USR) combines localized laser heating with high-frequency mechanical rolling to modify the near-surface state of Ti-6Al-4V. This study evaluated nine processing conditions formed by laser powers of 150, 200 and 250 W and nominal rolling-depth settings of 30, 50 and 70 µm. X-ray diffraction, sin²ψ residual-stress measurements, three-dimensional areal profilometry, HV0.2 microhardness testing and an experimentally calibrated MATLAB response-surface model were used to assess the coupled response. The lowest measured surface-topography values occurred at 150W-50D, with Sa = 0.406 µm, Sq = 0.524 µm, Sdq = 0.0754 and Sdr = 0.281%. The 200W-50D condition was also smooth, whereas 250W-70D produced the most severe roughening (Sa = 3.974 µm, Sq = 9.146 µm and Sdr = 4.616%). Microhardness reached a maximum of approximately 818 HV0.2 at 250W-50D, demonstrating that maximum hardening and minimum roughness did not coincide. Residual stress was predominantly compressive but strongly reflection-dependent; for example, 200W-70D gave -164.0 and +132.2 MPa for the two evaluated reflections. The MATLAB model reproduced Sa and Sq well in calibration (R² = 0.977 and 0.974), but leave-one-condition-out performance was weaker, particularly for residual stress (LOOCV R² = -0.879). The results identify a non-monotonic thermo-mechanical process window and show that LA-USR optimization requires simultaneous consideration of surface topography, hardness, crystallographic response and residual stress.
1 April 2025 in Scientia. Technology, Science and Society
Due to its high strength, good corrosion resistance, wear resistance, thermal stability, and oxidation resistance, high entropy alloys have great potential for application in engineering. High-entropy alloys based on the Al-Co-Cr-Fe-Ni system exhibit exceptional mechanical properties, including high strength, corrosion resistance, and thermal stability, making them promising candidates for engineering applications. This study investigates the microstructure and mechanical properties of AlxCoCrFeNi (x = 0.4, 0.8, 1.2) high entropy alloys fabricated via arc melting and laser melting deposition (LMD). Results demonstrate that increasing aluminum content induces a phase transition from a face-centered cubic (FCC) to a body-centered cubic (BCC) structure, significantly enhancing hardness from 163.1 HV (x = 0.4) to 513.7 HV (x = 1.2) while reducing ductility. The Al0.8CoCrFeNi alloy, with a balanced FCC/BCC biphasic structure, achieves optimal mechanical performance, exhibiting a compressive strength of 2105 MPa and 36.7% elongation. LMD-produced alloys display refined microstructures, such as eutectic formations, attributed to rapid cooling rates. The study highlights the critical role of aluminum in tailoring phase composition and mechanical behavior, offering insights for designing high entropy alloys with customized properties. However, challenges such as brittleness in high-Al-content alloys and unexplored anisotropy in LMD samples warrant further investigation. These findings advance the understanding of high entropy alloy processing-microstructure-property relationships, supporting their potential in high-performance applications.