11 January 2022 in IEEE Sensors Journal
Accurate multi-axis inertial sensing is required for self-positioning estimation in automatic driving and robot posture control. In particular, a small bias drift is an important requirement for these applications. The bias drift is primarily caused by the external stress from the package. To reduce the bias drift in micro electro-mechanical systems (MEMS) sensors, a stress isolation suspension (SIS) structure inside the sensor chip is considered promising for miniaturization and cost reduction. To easily design an effective SIS, we propose a new design procedure based on the topology optimization method (TOM). The number of elements for the TOM in MEMS devices is often large owing to narrow lines and gaps such as release holes and comb-shaped electrodes, which increasing the computational cost of a TOM using an iterative algorithm. Before the TOM iterative calculation, we first identify the dominant external force mode affecting the bias drift using a single finite element analysis (FEA) with precise detailed geometry. Based on this, the TOM model is simplified. This combination of FEA and TOM allows a biasreducing topology-optimized SIS (T-SIS) structure to be designed with reduced computational cost. For validation, we applied the T-SIS design procedure to a capacitive accelerometer for z-axis bias drift reduction and compared its performance to accelerometers without T-SIS. The experimental results indicate that the T-SIS reduces the z-axis bias drift from ±811 mG to ±9.9 mG (temperature range: -30 °C to +70 °C), which is 1/80 of the bias drift of the sensor without T-SIS.
15 February 2018 in Journal of Micromechanics and Microengineering
A wafer-level hermetic vacuum packaging technology intended for use with MEMS devices was developed based on a copper–tin (CuSn) thin film sealing ring. To allow hermetic packaging, the shear strength of the CuSn thin film bond was improved by optimizing the pretreatment conditions. As a result, an average shear strength of 72.3 MPa was obtained and a cavity that had been hermetically sealed using wafer-level packaging (WLP) maintained its vacuum for 1.84 years. The total pressures in the cavities and the partial pressures of residual gases were directly determined with an ultra-low outgassing residual gas analyzer (RGA) system. Hermeticity was evaluated based on helium leak rates, which were calculated from helium pressures determined with the RGA system. The resulting data showed that a vacuum cavity following 1.84 years storage had a total pressure of 83.1 Pa, contained argon as the main residual gas and exhibited a helium leak rate as low as 1.67 × 10 −17 Pa · m 3 s −1 , corresponding to an air leak rate of 6.19 × 10 −18 Pa · m 3 s −1 . The RGA data demonstrate that WLP using a CuSn thin film sealing ring permits ultra-high hermeticity in conjunction with long-term vacuum packaging that is applicable to MEMS devices.
11 February 2021 in Journal of Micromechanics and Microengineering
Silicon-on-insulator (SOI) wafers are used in many micro-electromechanical system (MEMS) devices because of their stable mechanical properties. However, one of the disadvantages of using the SOI configuration is residual stress deformation; strong residual stresses in the buried-oxide layer deform the device and deteriorate its performance. This could prevent the development of high-precision sensors and actuators. In recent years, a new deformation mode caused by this residual stress has been reported, involving tilting of the suspended MEMS structure owing to local deformation of the anchor. However, methods to solve this problem have not yet been proposed. In this study, we propose a simple T-shaped support as a solution to the tilt deformation. We verified its effects by finite element analysis and experiments; the proposed structure was observed to successfully reduce the tip displacement of a SOI-based cantilever by one-fourth. In addition, we applied the proposed method to a parallel-plate accelerometer as a demonstration to confirm that the sensitivity variations of the device reduced from 10.8% to 6.8% using the proposed support structure. Thus, we believe that the proposed design can contribute to the development of extremely accurate MEMS sensors and optical devices.
1 July 2025 in IEEJ Transactions on Sensors and Micromachines
We propose a triaxial gyroscope with a mounting structure composed of four non-rectangular building blocks with an inclined face on which a single-axis gyroscope is mounted. The mounting structure is designed considering high inter-axial orthogonality, stress resistance, and redundancy for three-axis angular rate detection in the event of failure. Injection molding and molded interconnected device technologies are used to produce plastic blocks with highly precise faces (face angle error: ±0.05°). A prototype is fabricated using blocks in which a Z-axis gyroscope is incorporated. The blocks are accurately positioned by pressing against an alignment jig. Three-axis test results obtained via a vector operation on the outputs of four Z-axis gyroscopes demonstrate a sensitivity to the applied angular rate of 100% for the main axis and ±0.2% for the other axes. An inter-axial orthogonality error of below 0.1° is also demonstrated. The proposed gyroscope detects the three-axis angular rates with low cross-axis sensitivity and has high inter-axial orthogonality.
14 January 2026 in IEEE Sensors Letters
Assembly-induced stresses such as printed circuit board (PCB) warpage and clamp loads propagate through the package to the MEMS die and perturb accelerometer bias. This letter presents a PCB-integrated stress-relief structure: a planar, fourfold-symmetric crab-leg (folded-beam) flexure that forms an “IMU island” via through-slots, attenuating stress transmission regardless of load direction while preserving four-sided routing. Finite-element analysis of a molded inertial measurement unit (IMU) package on a clamped–clamped PCB under mid-span deflection shows that the area-averaged von Mises stress at the MEMS anchor interface is reduced to 0.23× compared with a plain PCB. A clamped–clamped bending fixture with a recessed loading pin, load sensing, 3-D surface profiling, and a calibration–inference procedure maps measured displacements to a plain-PCB-equivalent surface stress, enabling fair comparison across layouts over an approximately ±40 MPa range. Measurements confirm that, relative to the plain PCB, accelerometer bias change decreases from 4.9 mG to 1.6 mG on X (0.32×) and from 48 mG to 8.4 mG on Z (0.18×), with no clear reduction on Y. These results demonstrate that board-level flexures reduce assembly-induced bias drift and provide a practical, user-implementable approach to stabilize MEMS IMU accelerometers without altering the device or package.
31 March 2025 in Measurement Science and Technology
This paper proposes a prototype device engineered to measure the optical properties of semiconductor films deposited on Si substrates under controlled stress conditions. Utilizing a four-point bending method enhanced with a displacement conversion mechanism, the device ensures the preservation of necessary optical paths for both reflected and transmitted light, which is essential for optical measurements. The design incorporates an indenter with an inclination of less than 0.02° within the four-point bending apparatus, enabling application of the stress necessary to change optical properties without fracturing the Si substrate. The flexure observed in the Si substrate upon stress application was found to closely align with theoretical predictions for four-point bending. Furthermore, this study established a direct proportionality between the stress dependence of the Raman shift and applied stress, with the proportionality coefficient matching those documented in the literature. The device has been successfully demonstrated to facilitate Raman spectroscopy measurements at a stress level of 600 MPa, doubling the previously reported threshold, without resulting in fractures of the Si wafer. This development presents a powerful tool for the assessment of semiconductor films on Si substrates, offering advanced insights into stress-dependent optical properties.